Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Avery Dennison Manuals
  4. Printer
  5. Monarch SIERRA SPORT4 9493
  6. Quick reference

Avery Dennison Monarch Sierra Sport4 9493 Quick Reference

Hide thumbs Also See for Monarch Sierra Sport4 9493:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual See also: Administrator's Manual
Q U I C K R E F E R E N C E
This Quick Reference contains supply loading information and
general care and maintenance procedures for the Monarch® Sierra
Sport4™ 9493™ printer. For more detailed information, refer to the
Operator's Handbook available on our Web site
(www.monarch.com).
U s i n g t h e B a t t e r y
You must charge the battery before using it for the first time.
Refer to the Operator's Handbook for important battery information.
1.
Review the safety information in the Regulatory Compliance
document included with your printer.
2.
Turn off the printer when you change batteries.
3.
Lay the printer down so the back of the printer faces up.
4.
Remove the plastic from a new battery.
5.
Slide the battery into the battery well in the bottom of the
printer until it latches into place.
Latch
®
Monarch
, Sierra Sport, and 9493 are trademarks of Paxar Americas, Inc.
TC9493QR Rev. AA 10/08
2008 Avery Dennison Corp.
All rights reserved.

Advertisement

loading

Related Manuals for Avery Dennison Monarch Sierra Sport4 9493

Summary of Contents for Avery Dennison Monarch Sierra Sport4 9493

  • Page 1 Slide the battery into the battery well in the bottom of the printer until it latches into place. Latch ® Monarch , Sierra Sport, and 9493 are trademarks of Paxar Americas, Inc. 2008 Avery Dennison Corp. TC9493QR Rev. AA 10/08 All rights reserved.
  • Page 2 To check the battery: The battery status flashes briefly when you turn on the printer. If the printer is already on, press A under P. Recharge the battery when the Error! Not a valid link. line is closer to the E (empty) instead of F (full).
  • Page 3 C o n n e c t i n g t h e C o m m u n i c a t i o n s C a b l e Open the cable door on the side of the printer by loosening the two screws with a Phillips screwdriver.
  • Page 4 L o a d i n g R i b b o n Use a ribbon to print on thermal transfer supplies. Open the printer and tip the ribbon cassette back if necessary and pull it towards you until it slides out of the printer. Rotate the two latches on side “A”...
  • Page 5 L o a d i n g S u p p l i e s Open the printer. Remove the tape from a new roll of supply. Push apart the supply holder tabs to widen the supply holder. Insert a roll of supplies so it unwinds from the top. Load supply for the print mode you want: non-peel, peel, or fan-fold.
  • Page 6 For fan-fold: Open the printer. Adjust the 4.8-inch (122 mm) core to the width of your fan-fold supplies by pushing or pulling on the supply guides on each side of the core. The guides move in 0.03-inch (0.8 mm) increments. Insert the core between the supply holder tabs to open them to their widest position.
  • Page 7 C l e a n i n g t h e P r i n t e r Do not use sharp objects or household cleaners to clean the printer. Use isopropyl alcohol on the interior areas only, never on the exterior.
  • Page 8 C l e a r i n g L a b e l J a m s When you are printing and a jam occurs, a supply error message appears. To clear the jam: Turn off the printer. Open the printer and remove the supply roll. Remove the jammed supplies with your fingers.