Mini-itx motherboard with 45 nm intel atom cpu ddr2 memory (up to 2 gb), vga, dvi, lvds, hdtv dual pcie gbe, compactflash, dual sata and pcie mini (190 pages)
Mini-itx single board computer with intel® atom™ n270 1.6 ghz processor, dual gigabit ethernet, audio, vga/ lvds/dvi-d/hdtv-out, six usb, nine rs-232, rs-232/422/485, compactflash® type ii, two sata, rohs compliant (178 pages)
Mini-itx motherboard with intel atom n270 cpu, 2 x sata, pci card slot, 2 x lvds, pcie mini card slot, vga, 6 x usb, gbe lan and rohs compliant (151 pages)
Mini-itx motherboard with intel atom n270 cpu, 2 x sata, pci card slot, 2 x lvds, pcie mini card slot, vga, 6 x usb, gbe lan and rohs compliant (150 pages)
Page 1
KINO-9454 Motherboard KINO-9454 Motherboard User Manual...
Page 2
REVISION HISTORY Title KINO-9454 Intel Pentium D/Celeron D Motherboard Revision Number Description Date of Issue Initial release September 2006 COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
Page 5
KINO-9454 Motherboard INSTALLATION AND CONFIGURATION ............63 4.1 A ..................64 STATIC RECAUTIONS 4.2 I ................64 NSTALLATION ONSIDERATIONS 4.2.1 Installation Notices ..................64 4.3 U ......................65 NPACKING 4.3.1 Unpacking Precautions..................65 4.3.2 Checklist......................66 4.4 KINO-9454 ............66...
Page 6
5.1.5 BIOS Menu Bar....................83 5.2 M ........................83 5.3 A ....................... 85 DVANCED 5.3.1 CPU Configuration..................86 5.3.2 IDE Configuration ................... 87 5.3.2.1 IDE Master, IDE Slave ................90 5.3.3 Super IO Configuration..................94 5.3.4 Hardware Health Configuration..............97 5.3.5 ACPI Configuration ..................
Page 7
KINO-9454 Motherboard WATCHDOG TIMER ..................153 ADDRESS MAPPING..................157 C.1 IO A ....................158 DDRESS C.2 1 MB M ................. 158 EMORY DDRESS C.3 IRQ M .................... 159 APPING ABLE C.4 DMA C ................159 HANNEL SSIGNMENTS EXTERNAL AC’97 AUDIO CODEC ..............161 D.1 I...
Page 12
List of BIOS Menus BIOS Menu 1: Main......................84 BIOS Menu 2: Advanced.....................86 BIOS Menu 3: CPU Configuration................87 BIOS Menu 4: IDE Configuration ................88 BIOS Menu 5: IDE Master and IDE Slave Configuration..........90 BIOS Menu 6: Super IO Configuration ..............94 BIOS Menu 7: Hardware Health Configuration............98 BIOS Menu 8: ACPI Configuration................
Page 13
KINO-9454 Motherboard Glossary AC ’97 Audio Codec 97 Hard Disk Drive ACPI Advanced Configuration and Integrated Data Electronics Power Interface Input/Output Advanced Power Management ICH4 I/O Controller Hub 4 ARMD ATAPI Removable Media Device L1 Cache Level 1 Cache ASKIR...
KINO-9454 Motherboard 1.1 KINO-9454 Overview The Mini-ITX form factor KINO-9454 with Pentium 4 / Pentium D / Celeron D CPU platform is fully equipped with latest technology and advanced multi-mode I/Os. The KINO-9454 is designed for system manufacturers, integrators, and VARs that want performance, reliability, and quality at a reasonable price.
KINO-9454 Motherboard 1.1.3 KINO-9454 Features Some of the KINO-9454 features are listed below: Complies with RoHS Supports Intel® Pentium 4 / Pentium D / Celeron D CPUs Supports a maximum front side bus (FSB) speed up to 1066MHz Supports up to 2GB of 400MHz, 533MHz or 667MHz of DDR2 memory Comes with two high performance gigabit Ethernet (GbE) controller Supports four SATA channels with transfer rates up to 3.0Gb/s...
1 x Serial port connector 4 x SATA II connectors 1 x TPM connector 2 x USB connectors The KINO-9454 has the following connectors on the board rear panel: 2 x Audio jacks 1 x CRT connector 2 x Ethernet connectors...
KINO-9454 Motherboard 1.2.2 Technical Specifications KINO-9454 technical specifications are listed in Table 1-1. Detailed descriptions of each specification can be found in Chapter 2 Detailed Specifications. SPECIFICATION ® ® ® ® CPUs Supported Intel Pentium 4 / Pentium D / Celeron...
KINO-9454 Motherboard Ethernet Dual Broadcom BCM5787 for PCI Express GbE with ASF2.0 remote control support BIOS AMI BIOS Label Power ATX power 170mm x 170mm (width x length) Physical Dimensions Operating Minimum: 0ºC (32°F) Temperature Maximum: 60°C (140°F) Table 1-1: Technical Specifications...
KINO-9454 Motherboard 2.1 Overview This chapter describes the specifications and on-board features of the KINO-9454 in detail. 2.2 Dimensions 2.2.1 Board Dimensions The dimensions of the board are listed below: Length: 170mm Width: 170mm Figure 2-1: KINO-9454 Dimensions (mm) IEI ® Technology, Corp.
KINO-9454 Motherboard ® ® 2.3.2 Intel Pentium ® ® The Intel Pentium 4 processor comes with the following features: Hyper-threading Technology improves system responsiveness and increases productivity and efficiency. Improved Power Management with Enhanced Intel SpeedStep® Technology Improved performance by allowing the system to address more than 4 GB of both virtual and physical memory.
Support a wide range of display types and configurations 2.6 Memory Support The KINO-9454 has two DDR2 DIMM sockets and supports two 400MHz, 533MHz or 667MHz DDR2 DIMM with a maximum RAM of up to 2GB. 2.7 PCI Bus Interface Support The PCI bus on the KINO-9454 has the following features: 33MHz Revision 2.3 is implemented...
4 x SATA drives 2 x IDE devices 2.9.1 SATA Drives The KINO-9454 supports four SATA II drives with transfer rates of up to 3.0 Gb/s. 2.9.2 IDE Interfaces The KINO-9454 IDE controller supports up to two IDE devices with the following...
The KINO-9454 supports eight USB interfaces, four internal and four external. The USB interfaces support USB 2.0. 2.14 BIOS The KINO-9454 uses a licensed copy of AMI BIOS. The features of the flash BIOS used are listed below: SMIBIOS (DMI) compliant...
2.16 Audio Codec The KINO-9454 has an integrated REALTEK ALC655 CODEC. The ALC655 CODEC is a 16-bit, full-duplex AC'97 Rev. 2.3 compatible six-channel audio CODEC designed for PC multimedia systems, including host/soft audio and AMR/CNR-based designs. Some of the features of the codec are listed below.
AVRack® Media Player Configuration Panel for improved user convenience 2.17 Power Consumption Table 2-2 shows the power consumption parameters for the KINO-9454 when a Pentium 4 processor with a clock speed of 3.06GHz is running with four DDR2 533MHz 1GB DIMM module.
KINO-9454 Motherboard 1 x Mini jumper pack 1 x Utility CD 1 x Quick Installation Guide 2.18.2 Optional Accessory Items The items shown in the list below are optional accessory items are purchased separately. ATI M56P mobile grade PCI Express Graphic Card with VGA, DVI, 1080i...
Page 32
KINO-9454 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK IEI ® Technology, Corp.
KINO-9454 Motherboard 3.1.2 Peripheral Interface Connectors Table 3-1 shows a list of the peripheral interface connectors on the KINO-9454. Detailed descriptions of these connectors can be found in Section 3.2. Connector Type Label ATX + CPU 12V power connector 4-pin header...
KINO-9454 Motherboard Table 3-1: Peripheral Interface Connectors 3.1.3 Rear Panel Connectors Table 3-2 lists the rear panel connectors on the KINO-9454. Detailed descriptions of these connectors can be found in Section 3.3. Connector Type Label Audio Jacks Audio connector CRT connector...
Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. This section has complete descriptions of all the internal, peripheral connectors on the KINO-9454. 3.2.1 ATX + CPU 12V Power Connector...
CN Pinouts: See Table 3-5 and Table 3-6 The cooling fan connectors on the KINO-9454 provide a 12V, 500mA current to a CPU cooling fan and a system cooling fan. All cooling fans have linear fan speed controlled by BIOS.
KINO-9454 Motherboard PIN NO. DESCRIPTION Ground +12V Rotation Signal Table 3-6: System Fan Connector Pinouts 3.2.3 Front Panel Connector CN Label: F_PANEL1 CN Type: 14-pin header (2x7) CN Location: See Figure 3-4 CN Pinouts: See Table 3-7 The front panel connector connects to several external switches and indicators to monitor and control the motherboard.
KINO-9454 Motherboard The DIO connector is managed through a Super I/O chip. The DIO connector pins are user programmable. The digital IO port of KINO-9454 is 5V CMOS level. Figure 3-5: Digital I/O Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION...
KINO-9454 Motherboard One primary 40-pin IDE device connector on the KINO-9454 motherboard supports connectivity to ATA 100 IDE devices with data transfer rates up to 100MB/s. Figure 3-6: IDE Device Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION RESET# GROUND...
KINO-9454 Motherboard Figure 3-7: IR Connector Location PIN NO. DESCRIPTION IR-RX Ground IR-TX Table 3-10: IR Connector Pinouts 3.2.7 Mini PCI Slot CN Label: MPCI1 CN Type: 124-pin Mini PCI Type III slot CN Location: See Figure 3-8 CN Pinouts: See Table 3-11 Mini PCI is a small form factor version of a PCI card.
KINO-9454 Motherboard 3.2.9 ATX Power Connector CN Label: PWR1 CN Type: 24-pin connector CN Location: See Figure 3-10 CN Pinouts: See Table 3-14 This 24-pin power connector supports the ATX power supply. Figure 3-10: Power Connector Location...
KINO-9454 Motherboard The four SATA drive connectors are connected to four SATA II drives. SATA II drives transfer data at speeds as high as 3.0Gb/s. Figure 3-12: SATA Drive Connector Locations PIN NO. DESCRIPTION Table 3-16: SATA Drive Connector Pinouts 3.2.12 TPM Connector...
KINO-9454 Motherboard CN Location: See Figure 3-13 CN Pinouts: See Table 3-17 The TPM (Trusted Platform Module) connector is a device with a controller that is used to check authenticity of digital signs and keys as well as other encryption and security functions.
KINO-9454 Motherboard Power Down# DRQ# Table 3-17: TPM Connector Pinouts 3.2.13 Internal USB Connectors CN Label: USB1 and USB2 CN Type: 8-pin header (2x4) CN Location: See Figure 3-14 CN Pinouts: See Table 3-18 One 2x4 pin connector provides connectivity to two USB 2.0 ports. The USB ports are used for I/O bus expansion.
3.3 External Interface Connectors The peripheral connectors on the back panel are connected to devices externally when the KINO-9454 is installed in a chassis. The peripheral connectors on the rear panel are: 2 x Audio jacks 1 x CRT connector...
KINO-9454 Motherboard CN Pinouts: See Figure 3-16 Line Out port (Lime): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers. Microphone (Pink): Connects a microphone. Figure 3-16: Audio Connector 3.3.2 CRT Connector...
CN Pinouts: See Table 3-20 The KINO-9454 is equipped with two built-in GbE Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN. The pin assignments are listed in the following...
KINO-9454 Motherboard Figure 3-20: External Serial Port Connector Description DATA CARRIER DETECT (DCD) RECEIVE DATA (RXD) TRANSMIT DATA (TXD) DATA TERMINAL READY (DTR) GROUND (GND) DATA SET READY (DSR) REQUEST TO SEND (RTS) CLEAR TO SEND (CTS) RING INDICATOR (RI) Table 3-23: External Serial Port Pinouts 3.3.6 USB Connectors...
4.1 Anti-static Precautions Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-9454. (Dry climates are especially susceptible to ESD.) It is therefore critical that whenever the KINO-9454 (or any other electrical component) is handled, the following anti-static precautions are strictly adhered to.
4.3.1 Unpacking Precautions Before installing the KINO-9454, unpack the motherboard. Some components on KINO-9454 are very sensitive to static electricity and can be damaged by a sudden rush of power. To protect it from being damaged, follow these precautions: The user should ground them self to remove any static charge before touching the KINO-9454.
CPU cooler (optional) USB cable (optional) If one or more of these items are missing, please contact the reseller or vendor the KINO-9454 was purchased from and do not proceed any further with the installation. 4.4 KINO-9454 motherboard Installation WARNING! 1.
CPU: An Intel® Pentium 4 Processor with HT Technology must be installed Chipset: An Intel® Chipset that supports HT Technology (that has been met by the KINO-9454) OS: An operating system that has optimizations for HT Technology 4.5.1.1 CPU Installation WARNING: CPUs are expensive and sensitive components.
When handling the CPU, only hold it on the sides. DO NOT touch the pins at the bottom of the CPU. To install Socket LGA775 CPU onto the KINO-9454, follow the steps below: Step 1: Remove the protective cover. Remove the black protective cover by prying it off the load plate.
KINO-9454 Motherboard Figure 4-2: Remove the CPU Socket Protective Shield Step 2: Open the socket. Disengage the load lever by pressing the lever down and slightly outward to clear the retention tab. Rotate the load lever to a fully open position.
12V power connector after the cooling kit is installed.Step 0: 4.5.2 Socket LGA775 Cooling Kit Installation WARNING: It is strongly recommended that you DO NOT use the original heat sink and cooler provided by Intel on the KINO-9454. IEI ® Technology, Corp.
KINO-9454 Motherboard The KINO-9454 is vertically mounted on a horizontal backplane, and Intel’s heat sink does not come with a support bracket on the soldering side, the PCB may be bent by the weight of the cooling kit. IEI’s cooling kit (CF-520 and CF-775A) includes a support bracket that is combined with the heat sink mounted on the CPU to counterweigh and balance the load on both sides of the PCB.
Step 6: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the KINO-9454. Carefully route the cable and avoid heat generating chips and fan blades.Step 0:...
Please only use DDR2 DIMM modules. 4.5.3.2 DIMM Module Installation The KINO-9454 has four DDR2 SDRAM DIMM sockets. Follow the steps below to install the DIMM module. Step 1: Make sure the two handles of the DIMM socket are in the "open" position,...
KINO-9454 Motherboard Figure 4-7: Installing the DIMM Module Step 2: Slowly slide the DIMM module along the plastic guides on both ends of the socket. Press the DIMM module down into the socket until it clicks into position and the two handles have automatically locked the memory module into place (Figure 4-8).
KINO-9454 Motherboard Quantity Type IDE flat cable SATA cables SATA power cable Table 4-1: IEI Provided Cables 4.5.4.1 IDE Disk Drive Connector (IDE1) The cable used to connect the motherboard to the IDE device is a standard 40-pin ATA/100 flat cable. To connect an IDE device to the motherboard, follow the instructions below.
4.5.4.2 COM Port Connectors The KINO-9454 provides four serial ports interfaced through one 14-pin male headers (COM3) and three DB-9 connector. The serial ports facilitate the connection to serial devices or a communications network, e.g., terminal console.
Jumper Location: See Figure 4-11 If the KINO-9454 fails to boot due to improper BIOS settings, use this jumper to clear the CMOS data and reset the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
KINO-9454 Motherboard Enter the correct CMOS setting Load Optimal Defaults Load Failsafe Defaults. After having done one of the above, save the changes and exit the CMOS Setup menu. Clear CMOS DESCRIPTION Open Normal Operation (Default) Closed Clear CMOS Setup Table 4-3: Clear CMOS Jumper Settings The clear CMOS jumper is located in Figure 4-11.
KINO-9454 Motherboard To mount the motherboard into a chassis please refer to the chassis user guide that came with the product. 4.8 Rear Panel Connectors 4.8.1 LCD Panel Connection The conventional CRT monitor connector is a 15-pin, female D-SUB connector. Pin assignments can be seen in that can be connected to external monitors.
Page 80
KINO-9454 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK IEI ® Technology, Corp.
KINO-9454 Motherboard 5.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed.
KINO-9454 Motherboard F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears.
KINO-9454 Motherboard BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed. The items shown in the system overview include: AMI BIOS: Displays auto-detected BIOS information...
KINO-9454 Motherboard System Time [xx:xx:xx]: The system time is set here. System Date [Day xx/xx/xxxx]: The system date is set here. 5.3 Advanced The Advanced menu (BIOS Menu 2) allows access to the CPU and peripheral device configuration options through the following sub-menus:...
KINO-9454 Motherboard BIOS Menu 2: Advanced 5.3.1 CPU Configuration The CPU Configuration menu (BIOS Menu 3) shows detailed CPU specifications and CPU configuration options. IEI ® Technology, Corp.
KINO-9454 Motherboard BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed...
KINO-9454 Motherboard BIOS Menu 4: IDE Configuration ATA/IDE Configuration [Enhanced] The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device mode. Disabled Disable all ATA/IDE ports. No Primary/Secondary IDE mode is presented for configuration Compatible If this option is selected, “Legacy IDE Channels” option is presented for configuration.
Page 89
KINO-9454 Motherboard Configure SATA as [IDE] Use the Configure SATA as option to specify how to configure the available SATA devices. Enables the SATA devices as IDE devices EFAULT Enables the SATA devices as a RAID device RAID AHCI Enables Native Command Queuing (NCQ) and SATA hot...
KINO-9454 Motherboard The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the IDE devices installed in the system. If an IDE device is detected, and one of the above listed four BIOS configuration options are selected, the IDE configuration options shown in Section 5.3.2.1 appear.
Page 91
KINO-9454 Motherboard Size: The size of the device. LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a method of addressing data on a disk drive is supported or not. Block Mode: Block mode boosts IDE drive performance by increasing the amount of data transferred.
Page 92
KINO-9454 Motherboard LS-120 LBA/Large Mode [Auto] The LBA/Large Mode BIOS option disables or auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB.
Page 93
KINO-9454 Motherboard PIO mode 0 selected with a maximum transfer rate of 3.3MBps PIO mode 1 selected with a maximum transfer rate of 5.2MBps PIO mode 2 selected with a maximum transfer rate of 8.3MBps PIO mode 3 selected with a maximum transfer rate of 11.1MBps PIO mode 4 selected with a maximum transfer rate of 16.6MBps...
KINO-9454 Motherboard Disabled Prevents the BIOS from using 32-bit data transfers. Enabled Allows BIOS to use 32-bit data transfers on support hard EFAULT disk drives. 5.3.3 Super IO Configuration The Super IO Configuration menu (BIOS Menu 6) sets or changes the configurations for the FDD controllers, parallel ports and serial ports.
Page 95
KINO-9454 Motherboard address is IRQ4 3E8/IRQ4 Serial Port 1 I/O port address is 3E8 and the interrupt address is IRQ4 2E8/IRQ3 Serial Port 1 I/O port address is 2E8 and the interrupt address is IRQ3 Serial Port2 Address [2F8/IRQ3] The Serial Port2 Address option allows BIOS to select the Serial Port 2 base address.
Page 96
KINO-9454 Motherboard Serial Port3 Address [3E8] This option allows BIOS to select the base addresses for serial port 3 Disabled No base address is assigned to serial port 3 Serial port 3 I/O port address is 3E8 EFAULT Serial port 3 I/O port address is 2E8...
KINO-9454 Motherboard Serial port 4 IRQ address is 11 Serial Port5 Address [2E0] This option allows BIOS to select the base addresses for serial port 5. Disabled No base address is assigned to serial port 5 Serial port 5 I/O port address is 3E8...
KINO-9454 Motherboard BIOS Menu 7: Hardware Health Configuration FAN 1 Mode Setting: [Full On] The FAN 1 Mode Setting has the following options: If selected, there are no additional configurable options. Full On EFAULT Automatic If selected, the following options will appear with values...
Page 99
KINO-9454 Motherboard FAN 2 Mode Setting: [Full On] The FAN 2 Mode Setting has the following options: Full On If selected, there are no additional configurable options. EFAULT Automatic If selected, the following options will appear with values Mode that can be configured:...
KINO-9454 Motherboard The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: The following system temperatures are monitored CPU Temperature System Temperature Fan Speeds: The CPU cooling fan speed is monitored. Fan1 Speed...
KINO-9454 Motherboard BIOS Menu 8: ACPI Configuration ACPI Aware O/S [Yes] Use the ACPI Aware O/S option to enable the system to configure ACPI power saving options. ACPI can only be implemented if the system OS complies with the ACPI standard.
KINO-9454 Motherboard BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration] Suspend mode [S1 (POS)] Use the Suspend Mode option to specify the sleep state the system enters when it is not being used. S1 (POS) The system enters S1(POS) sleep state. The system EFAULT appears off.
KINO-9454 Motherboard BIOS Menu 10: APM Configuration Power Management/APM [Enabled] The Power Management/APM BIOS option accesses the advanced power management features. Disabled Disables the Advanced Power Management (APM) feature Enabled Enables the APM feature EFAULT Power Button Mode [On/Off] The Power Button Mode BIOS specifies how the power button functions.
Page 104
KINO-9454 Motherboard Suspend When the power button is pressed the system goes into suspend mode Restore on AC Power Loss [Last State] The Restore on AC Power Loss BIOS option specifies what state the system returns to if there is a sudden loss of power to the system.
KINO-9454 Motherboard Resume On RTC Alarm [Disabled] The Resume On RTC Alarm determines when the computer will be roused from a suspended state. Disabled The real time clock (RTC) cannot generate a wake EFAULT event Enabled If selected, the following will appear with values that...
KINO-9454 Motherboard BIOS Menu 11: MPS Configuration MPS Revision [1.4] Use the Multiprocessor Specification (MPS) for OS option to specify the MPS version to be used. MPS version 1.1 is used MPS version 1.4 is used EFAULT 5.3.8 Smbios Configuration Use the Smbios Configuration menu (Error! Reference source not found.) to configure...
KINO-9454 Motherboard BIOS Menu 12: Smbios Configuration [Advanced] Smbios Smi Support [Enabled] Use the Smbios Smi Support to enable the system to support the SMBIOS SMI wrapper for the PnP function 50h – 54h. Disabled SMBIOS SMI wrapper for the PnP function 50h – 54h not...
KINO-9454 Motherboard BIOS Menu 13: Remote Access Configuration [Advanced] Remote Access [Enabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled Remote access is disabled. Enabled Remote access configuration options shown below...
Page 109
KINO-9454 Motherboard Terminal Type VT-UTF8 Combo Key Support These configuration options are discussed below. Serial Port Number [COM1] Use the Serial Port Number option allows to select the serial port used for remote access. COM1 System is remotely accessed through COM1...
Page 110
KINO-9454 Motherboard NOTE: Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave Flow Control [None] Use the Flow Control option to report the flow control method for the console redirection application.
KINO-9454 Motherboard VT-UTF8 Combo Key Support [Enabled] Use the VT-UFT8 Combo Key Support option to enable additional keys that are not provided by VT100 for the PC 101 keyboard. The VT100 Terminal Definition is the standard convention used to configure and conduct emergency management tasks with UNIX-based servers.
KINO-9454 Motherboard BIOS Menu 14: USB Configuration USB Configuration The USB Configuration field shows the system USB configuration. The items listed are: Module Version: x.xxxxx.xxxxx USB Devices Enabled The USB Devices Enabled field lists the USB devices that are enabled on the system...
Page 113
KINO-9454 Motherboard 6 USB Ports Six USB ports are activated. 8 USB Ports Eight USB ports are activated. EFAULT USB 2.0 Controller [Enabled] Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller Enabled USB 2.0 controller enabled EFAULT USB 2.0 controller disabled...
KINO-9454 Motherboard USB2.0 Controller Mode [HiSpeed] Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller. FullSpeed The controller is capable of operating at 12Mb/s HiSpeed The controller is capable of operating at 480Mb/s EFAULT 5.3.10.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (BIOS Menu 14) to configure USB mass storage class devices.
KINO-9454 Motherboard BIOS Menu 16: Boot 5.4.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 17) to configure advanced system boot options.
KINO-9454 Motherboard BIOS Menu 17: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. No POST procedures are skipped Disabled Enabled Some POST procedures are skipped to decrease...
Page 117
KINO-9454 Motherboard AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS The system forces third party BIOS to display EFAULT during system boot. Keep Current The system displays normal information during system boot.
KINO-9454 Motherboard Boot From LAN Support [Disabled] The BOOT From LAN Support option enables the system to be booted from a remote system. Disabled Cannot be booted from a remote system through the EFAULT Enabled Can be booted from a remote system through the 5.4.2 Boot Device Priority...
KINO-9454 Motherboard 5.4.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. When the menu is opened, the HDDs connected to the system are listed as shown below: 1st Drive [HDD: PM-(part number)] NOTE: Only the drives connected to the system are shown.
KINO-9454 Motherboard The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available FDDs is shown. Select the first FDD the system boots from. If the “1st Drive” is not used for booting this option may be disabled.
KINO-9454 Motherboard listed. The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available CD/DVD drives is shown. Select the first CD/DVD drive the system boots from. If the “1st Drive” is not used for booting this option may be disabled.
KINO-9454 Motherboard Change User Password Use the Change User Password to set or change a user password. The default for this option is Not Installed. If a user password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change User Password.
KINO-9454 Motherboard BIOS Menu 22:NorthBridge Chipset Configuration DRAM Frequency [Auto] Use the DRAM Frequency option to specify the DRAM frequency or allow the system to automatically detect the DRAM frequency. Auto Automatically selects the DRAM frequency EFAULT 400MHz Sets the DRAM frequency to 400MHz...
Page 125
KINO-9454 Motherboard components such as CAS and bank cycle time as well as valid settings for the module and the manufacturer's code. The SPD enables the BIOS to read the spec sheet of the DIMMs on boot-up and then adjust the memory timing parameters accordingly.
KINO-9454 Motherboard PCI/IGD PCI/PEG PEG/IGD PEG/PCI EFAULT Internal Graphics Mode Select [Enable, 8MB] Use the Internal Graphic Mode Select option to specify the amount of system memory that can be used by the Internal graphics device. Disable Enable, 1MB 1MB of memory used by internal graphics device...
Page 127
KINO-9454 Motherboard Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program. Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system.
Page 128
KINO-9454 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK IEI ® Technology, Corp.
To install the chipset driver, please follow the steps below: Step 1: Insert the CD into the system that contains the KINO-9454 board. Open the 1-INF directory and locate the icon for the infinst_autol.exe installation file. Once located, use the mouse to double click the icon.
KINO-9454 Motherboard Figure 6-3: License Agreement Step 5: Agree to the license terms by clicking “Y ”. The “Readme” in Figure 6-4 appears. Figure 6-4: Readme Information Step 6: Click “Y ”. The driver is installed on the computer. After the installation is complete, the installation complete screen shown in Figure 6-5 appears.
KINO-9454 Motherboard Step 0: Figure 6-5: Restart the Computer 6.3 VGA Driver To install the VGA driver, please follow the steps below: Step 1: Insert the Utility CD that came with the motherboard into the system CD drive. Step 2: Open the X:\2-VGA\WIN2K_XP directory (where X:\ is the system CD drive) and double-click the win2k_xp1420.exe installation file.
KINO-9454 Motherboard installation. Figure 6-8: VGA Driver Installation Welcome Screen Step 6: A license agreement shown in Figure 6-9 appears. Read through the license agreement. Figure 6-9: VGA Driver License Agreement Step 7: Accept the terms and conditions stipulated in the license agreement by clicking...
KINO-9454 Motherboard the “Y ” button (Figure 6-9). The installation notice shown in Figure 6-10 appears. Figure 6-10: VGA Driver Installing Notice Step 8: After the driver installation process is complete, a confirmation screen shown in Figure 6-11 appears. Figure 6-11: VGA Driver Installation Complete...
KINO-9454 Motherboard 6.4 Broadcom LAN Driver (for GbE LAN) Installation To install the Broadcom LAN driver, please follow the steps below. Step 1: Open Windows Control Panel (Figure 6-12). Figure 6-12: Access Windows Control Panel Step 2: Double click the System icon (Figure 6-13).
KINO-9454 Motherboard Figure 6-15: Device Manager List Step 5: Double click the listed device that has question marks next to it. (This means Windows does not recognize the device). Step 6: The Device Driver Wizard appears (Figure 6-16). Click N to continue.
KINO-9454 Motherboard Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 6-17). Click N to continue. Figure 6-17: Locate Driver Files Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx Drivers” directory (Figure 6-18) in the location browsing window, where “X:\” is the system CD drive.
KINO-9454 Motherboard Step 9: Click OK to continue. A driver files location menu window appears. Click N continue. The driver is installed.Step 0: 6.5 RealTek Audio Driver (ALC655) Installation To install the Realtek Audio driver, please follow the steps below.
KINO-9454 Motherboard Figure 6-20: Audio Driver Install Shield Wizard Starting Step 3: The Setup Status screen appears as the driver is installed (Figure 6-21). Figure 6-21: Audio Driver Setup Preparation Step 4: At this stage the Digital Signal Not Found screen appears (Figure 6-22). Click to continue.
KINO-9454 Motherboard Figure 6-22: Audio Driver Digital Signal Step 5: The audio driver installation continues (Figure 6-23). Figure 6-23: Audio Driver Installation Continues Step 6: After the driver installation process is complete, a confirmation screen appears (Figure 6-24).
KINO-9454 Motherboard Figure 6-24: Audio Driver Installation Complete Step 7: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click F INISH restart the computer.Step 0: 6.6 Intel Matrix Storage Manager Installation...
KINO-9454 Motherboard Figure 6-25: Preparing Setup Screen Step 4: A Welcome screen appears. Click N to continue the installation. Step 5: A license agreement appears. Read through the license agreement. Step 6: The “Uninstallation Warning” window appears. Click on the N button to continue.
Page 146
KINO-9454 Motherboard take effect the computer must be restarted. Once decided when to restart the computer, click the “F ” button. Step 0: INISH IEI ® Technology, Corp.
KINO-9454 Motherboard A.1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 5. System Overview .....................84 ATA/IDE Configuration [Enhanced] ...............88 Configure SATA as [IDE] ..................89 Configure SATA Channels [Before PATA]............89 IDE Master and IDE Slave ..................89 Auto-Detected Drive Parameters ................90...
Page 149
KINO-9454 Motherboard Fan 1 Start PWM ......................98 Slop PWM 1 ......................98 FAN 2 Mode Setting: [Full On]................99 Temperature 2 Limit of OFF..................99 Temperature 2 Limit of Start...................99 Temperature 2 Limit of Full ..................99 Fan 2 Start PWM ......................99 Slop PWM 2 ......................99 FAN 3 Mode Setting: [Full On]................99...
Page 150
KINO-9454 Motherboard Terminal Type ....................... 109 VT-UTF8 Combo Key Support ................109 Serial Port Number [COM1] ................. 109 Base Address, IRQ [3F8h, 4] ................109 Serial Port Mode [115200 8,n,1]................109 Flow Control [None] ..................... 110 Redirection After BIOS POST [Always] .............. 110 Terminal Type [ANSI] ...................
Page 154
KINO-9454 Motherboard NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
Page 155
KINO-9454 Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example program: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
Page 156
KINO-9454 Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK IEI ® Technology, Corp.
KINO-9454 Motherboard D.1 Introduction The motherboard comes with an on-board Realtek ALC655 CODEC. Realtek ALC655 is a 16-bit, full duplex AC’97 Rev. 2.3 compatible audio CODECwith a sampling rate of 48KHz. D.1.1 Accessing the AC’97 CODEC The CODEC is accessed through three phone jacks on the rear panel of the motherboard.
KINO-9454 Motherboard D.2 Sound Effect Configuration D.2.1 Accessing the Sound Effects Manager To access the Sound Effects Manager, please do the following: Step 1: Install the audio CODEC driver. Step 2: Click either: The Sound Effect Manager icon in the Notification Area of the system task bar (see Figure D-2), or The Sound Effect Manager icon in the Control Panel (see Figure D-3).
KINO-9454 Motherboard FigureeD-4: Sound Effects Manager (ALC655) NOTE: The Sound Effect Manager shown in Figure D-4 is for the RealTek ALC655 audio CODEC. Different CODECs may have different sound manager appearances. The following section describes the different configuration options in the Sound Effect Manager.
Page 165
KINO-9454 Motherboard NOTE: The Karaoke Mode is configured in the Sound Effect menu. To access Karaoke configuration settings, click on the Sound Effect menu tab. Sound Effect Karaoke Mode Equalizer Speaker Configuration Speaker Test S/PDIF-In S/PDIF-Out Connector Sensing HRTF Demo...
Page 166
KINO-9454 Motherboard that fits a certain vocal range. Equalizer Selection:- Preset equalizer settings enable easy audio range settings. Ten frequency bands can be configured. Speaker Configuration:- Multi-channel speaker settings are configured in this menu. Configurable options include: Headphone Channel mode for stereo speaker output Channel mode for 4 speaker output Channel mode for 5.1 speaker output...