Reverse Procedure To Reassemble Oven Door; Clock/Timer Mechanism, Spark Module, And High Limit Sensor; Cooktop, Top Burner Gas Valves, Top Burner Bases, Top Burner Venturies, And Spark Electrodes; Spark Switches - Amana Gas Freestanding BIG OVEN Service Manual

Disassembly Procedures
!
Reverse Procedure to Reassemble Oven
Door
• Position slot on oven door hinge arms into the hinge
receivers. When slot is engaged into the hinge
receivers, open the door just far enough to rotate both
hinge locking tabs to the UNLOCK position.
Clock/Timer Mechanism, Spark Module, and
High Limit Sensor
1. Turn off electric supply to oven.
2. Using a "stubby" phillips screwdriver remove the
offset screws from the bottom front of control panel.
Spark
module
High limit
sensor
Offset
screws
3. Rotate bottom of control panel outward, then lift up to
disengage top tabs.
4. Place control panel on a protective padded surface
with the clock/timer down. Remove screws securing
CLOCK/TIMER MECHANISM to mounting bracket.
There is sufficient extra wire length to twist clock/
timer mechanism out of the way while installing new
mechanism. Transfer electrical wires/connectors one
at a time to new mechanism.
5. Depress double tab on top of SPARK MODULE and
remove from rear cover. Reconnect wires one at a
time to new spark module.
6. HIGH LIMIT switch is attached to bracket by screws.
NOTE: When reinstalling control panel, be certain the
fiberfax insulation and it's galvanized retainer is
above the flue cutout in control panel. Insulation
and retainer are NOT visible when correctly
positioned. Verify backguard heat shield (above
flue) is below backguard panel and visible when
installed.
7. Reverse procedure to reattach control panel to range.
RS2310005 Rev. 0
WARNING
Clock
Overlay
Disconnect power source and shut off gas supply before
servicing, unless testing requires it.
Cooktop, Top Burner Gas Valves, Top
Burner Bases, Top Burner Venturies, and
Spark Electrodes
1. Turn off gas supply and disconnect gas supply line.
2. Turn off electrical supply to range.
3. Remove all four top burner control knobs.
4. Remove screws securing manifold panel.
5. Rotate bottom of manifold panel outward to
disengage from tabs located on top.
NOTE: When reinstalling manifold panel hooks. Place
the top tabs first, then position manifold panel
ABOVE flange on range front frame.
6. Remove top burner grates and cast burner caps.
7. Remove screws securing each BURNER BASE to
cooktop/burner venturi.
8. Disconnect spark electrode wire from each burner
base. Mark each burner base LF, RF, LR, and RR to
avoid mix up later.
9. Remove screw securing BURNER SPARK
ELECTRODES to burner base.
10. Lift up on front of COOKTOP and pull forward.
11. Move top burner venturi off TOP BURNER GAS
VALVE being serviced.
12.Using a ¼–inch nut driver remove screw securing gas
valve to gas manifold pipe.
13.Reverse procedure to install new top burner gas
valve.
NOTE: Verify gas connection fittings are tight using
soapy water.

Spark Switches

1. Disconnect electrical supply to range.
2. Remove manifold panel cover, see previous section.
3. Gently pull forward on switch wires on left side until
the ¼–inch electrical disconnects can be
disconnected.
4. The spark switches are supplied in sets of four.
Remove switches from each top burner gas valve.
Reconnect ¼–inch connectors.
5. Reverse procedure to reassemble and check
operation.

Oven Bottom

1. Remove thumb screws securing oven bottom to oven
cavity brackets, located in the rear of the oven cavity.
2. Lift at the rear and slide oven bottom away from the
front oven frame.
3. Remove oven bottom from oven cavity.
18