Confi Guring Home City Settings - Casio 5325 Operation Manual

Timekeeping
To enter the Timekeeping Mode, hold down C at least two seconds.
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Upper Dial Hand: Indicates the current hour in the Home City time in
b Lower Dial Hand: Points to the day of the week.
n Day Indicator
E-24
STD/DST Switching
You can select summer time or standard time independently for each city. The initial default setting for all
cities is AUTO.
Normally you should use the AUTO setting because it automatically switches between summer time
and standard time. You should change the setting to STD (standard time) or DST (summer time) in the
following cases.
− When using a time of a location that is not included in the watch's list of 29 cities
When the preset AUTO standard time/summer time timing is incorrect for some reason
−
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time.
Remember that not all countries or even local areas use Daylight Saving Time.
 Note that you cannot switch between STD (standard time) and DST (daylight saving time) while UTC*
is selected as your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. The reference point for
UTC is Greenwich, England.
E-26
Confi guring Current Time and Day Settings Manually
You can confi gure current time and day settings manually when the watch is unable to receive a time
calibration signal.
To change the current time setting manually
1. Pull out the crown.
 This will cause the x Second Hand to move to the city code of the
currently selected Home City.
 If you do not perform any operation with the crown for about two
minutes after pulling it out, crown operations will become disabled and
the hand will not move if you rotate the crown. If this happens, push the
crown back in and then pull it out again.
2. Change the Home City settings, if you want.
TYO (TOKYO)
 For details about these settings, see step 2 under "To confi gure Home
City settings" (page E-25).
3. Hold down C for about one second until the watch beeps and the
x Second Hand moves to 12 o'clock.
 This indicates the manual time setting mode.

In the following steps, each press of C cycles between settings as
shown below.
E-28
To change the current day setting manually
1. Pull out the crown.
 This will cause the x Second Hand to move to the city code of
the currently selected Home City.
2. Hold down C for about one second until the watch beeps and the
x Second Hand moves to 12 o'clock.
 This indicates the manual time setting mode.
3. Press C twice. This will enter the day setting mode.

The n Day Indicator will move slightly to indicate the setting
mode.
4. Rotate the crown to adjust the day setting.
Dec 5. After the n Day Indicator stops moving, press C. This will enter
Nov Jan
the month setting mode.
Oct Feb
 The x Second Hand will move to the currently selected month.
6. Rotate the crown to adjust the month setting.
7. Press C. This will enter the year setting mode.
Sep Mar
 The z Hour Hand will move to the number that represents the
tens digit of the year and the c Minute Hand will move to the
number that represents the ones digit. The x Second Hand will
Aug
Apr
move to 12 o'clock and stop there.
Jul May
Jun
Setting the month
E-30
Operation Guide 5325
24-hour format.
Confi guring Home City Settings
The Home City is location where you will normally use the watch. You can choose from a selection of city
codes that represent 29 cities around the globe.
To confi gure Home City settings
Note
 This watch does not have a city code that corresponds to Newfoundland.
1. Pull out the crown.
 This will cause the x Second Hand to move to the city code of the
currently selected Home City.
 This indicates the city code setting mode.
 If you do not perform any operation with the crown for about two
minutes after pulling it out, crown operations will become disabled and
TYO (TOKYO)
the hand will not move if you rotate the crown. If this happens, push the
crown back in and then pull it out again.

For details about city codes, see the "City Code Table" at the back of
this manual.
2. Rotate the crown to move the x Second Hand to the city code you want to
select as your Home City.
 Each time you select a city code, the z Hour Hand, c Minute Hand
and n Day Indicator move to the current time and day for that city
code.
3. Push the crown back in to return to the Timekeeping Mode.
To switch between standard time and summer time manually
1. Perform steps 1 and 2 under "To confi gure Home City settings" (page E-25).
 Selecting a city code will cause the z Hour Hand, c Minute Hand, and v Upper Dial Hand to
move automatically to the current time for the selected city code.

If you will use the watch in a city that is not included in the city code list, select a city code that is in
the same time zone as your city.

Displaying the Home City Settings screen will cause the b Lower Dial Hand to move to AUTO (auto
switching), STD (standard time), or DST (daylight saving time).
The watch automatically switches between standard time and daylight saving time in accordance
AUTO
with its calendar.
STD The watch always shows standard time.
DST The watch always shows daylight saving time.
2. Hold down A for about one second to cycle through the summer time settings
as shown below.
A
AUTO
3. After the setting is way you want, push the crown back in.
Home city/DST
C
Hour/Minute
C
Year
C
4. Rotate the crown to adjust the time (hour and minute) setting.
 See "Using the Crown" (page E-3) for information about high-speed hand movement.

The v Upper Dial Hand is synchronized with the z Hour Hand.
 When adjusting the setting, check to make sure that the v Upper Dial Hand correctly indicates an
a.m. time or p.m. time.
 If you want to change the day setting at this time, press C and perform the procedure starting from
step 3 under "To change the current day setting manually" (page E-30).
5. After the settings are the way you want, push the crown back in to return to the Timekeeping Mode.

This causes timekeeping to resume with the x Second Hand starting from 12 o'clock.
8. Rotate the crown to adjust the year setting.
 If you want to change the time setting at this time, press C and then perform the procedure starting
from step 4 under "To change the current time setting manually" (page E-28).
0
1
2
9 3
8 4
7 5
6
Year setting (ones digit)
9. After the settings are the way you want, push the crown back in to return to the Timekeeping Mode.
 This causes timekeeping to resume with the x Second Hand starting from 12 o'clock.
Note
 The watch's built-in full automatic calendar makes allowances for different month lengths and leap
years. Once you set the day, there should be no reason to change it except after you have the watch's
rechargeable battery replaced or after power drops to Level 3.
A
STD DST
A
C
Hour
C
Month Day
C
00
10
20
90 30
80 40
70 50
60
Year setting (tens digit)
E-25
E-27
E-29
E-31