Selecting a Mode
•
The illustration below shows which buttons you need to press to navigate between modes.
To return to the Timekeeping Mode from any other mode, hold down D for about two seconds.
•
In any mode, press L to illuminate the display.
•
Countdown
Countdown
Timer Mode
Timer Mode
Stopwatch Mode
Stopwatch Mode
World Time
World Time
Alarm Mode
Alarm Mode
Mode
Mode
E-24
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Auto Return Features
•
The watch returns to the Timekeeping Mode automatically if you do not perform any button operation
for two or three minutes in the Data Recall, Alarm, Receive, or Hand Home Position Adjustment Mode.
•
If you leave a screen with fl ashing digits on the digital display for two or three minutes without
performing any operation, the watch exits the setting screen automatically.
Initial Screens
When you enter the Data Recall, World Time, Alarm, Compass, or Barometer/Thermometer Mode, the
data you were viewing when you last exited the mode appears fi rst.
Scrolling
The A and C buttons are used to scroll through settings on the digital display while a setting screen is
displayed, and to move the hands of the watch manually. In most cases, holding down either of these
buttons will perform its operation at high speed.
E-26
Confi guring Home City Settings
There are two Home City settings: selecting the Home City, and specifying either standard time or daylight
saving time (DST).
To confi gure Home City settings
PM
PM
1. In the Timekeeping Mode, hold down E until each of the following
indicator
indicator
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
•
For information about city codes, see the "City Code Table" at the
back of this manual.
2. To change the Home City code setting, press A to move the second
hand clockwise.
Keep pressing A until the second hand is pointing to the city code
•
Second
Second
Hour :
Hour :
hand
hand
you want to select as your Home City.
Minutes
Minutes
City code
City code
•
The current time in the time zone of the currently selected city code is
shown on the digital display.
DST indicator
DST indicator
3. Press D. This will display the DST setting screen on the digital
display.
4. Use A to cycle through the DST settings as shown below.
Auto DST (AUTO)
E-28
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down E until each of the following
DST indicator
DST indicator
steps occurs.
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Press D. This will display the DST setting screen on the digital
display.
3. Use A to cycle through the DST settings as shown below.
Auto DST (AUTO)
•
The Auto DST ( AUTO ) setting can be selected only when a city code that supports time calibration
signal reception (page E-15) is selected. While Auto DST is selected, the DST setting changes
automatically in accordance with DST information included in the received time calibration signal.
4. After all the settings are the way you want, press E to exit the setting screen.
•
The dSt indicator indicates that Daylight Saving Time is selected.
E-30
Operation Guide 5114 5214
Timekeeping Mode
Timekeeping Mode
Data Recall
Data Recall
Mode
Mode
Hand Home Position
Hand Home Position
Receive Mode
Receive Mode
Adjustment Mode
Adjustment Mode
DST off (OFF)
DST on (On)
DST off (OFF)
DST on (On)
You can use buttons A, B, and C to enter a sensor mode directly from the Timekeeping Mode or
•
from another sensor mode. To enter a sensor mode from the Data Recall, Stopwatch, Countdown
Timer, Alarm, World Time, Receive, or Hand Home Position Adjustment Mode, fi rst enter the
Timekeeping Mode and then press the applicable button.
•
The hour and minute hands indicate the current time in all modes. In the Timekeeping, Data Recall,
Stopwatch, Countdown Timer, and Alarm modes, the second hand indicates the current (Timekeeping
Mode) second. The second hand performs other operations in the other modes.
Sensor Modes
Sensor Modes
Compass Mode
Compass Mode
Thermometer Mode
Thermometer Mode
Timekeeping
Use the Timekeeping Mode ( HOME) to set and view the current time and date.
In the Timekeeping Mode, press E to toggle the digital display between the day of the week and the
•
barometric pressure graph.
Day of the Week
Second
hand
Hour
hand
Minute
hand
Month Day
Day of week
•
The Auto DST ( AUTO ) setting will be available only when a city code that supports time calibration
signal reception (page E-15) is selected as the Home City. While Auto DST is selected, the DST
setting is changed automatically in accordance with time calibration signal data.
•
Note that you cannot switch between standard time and daylight saving time (DST) while UTC is
selected as your Home City.
5. After all the settings are the way you want, press E to return to the Timekeeping Mode.
•
The hands of the watch will move the current time in the zone where the city code you selected as
your Home City is located. Do not perform any operation on the watch while the hands are moving.
•
If Daylight Saving Time is selected, the dSt indicator will be on the digital display.
Note
•
After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate the
current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping.
The reference point for UTC is Greenwich, England.
•
Selecting some city codes automatically makes it possible for the watch to receive the time
calibration signal for the corresponding area. See page E-15 for details.
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time and date settings manually
1. In the Timekeeping Mode, hold down E until each of the following
PM
PM
steps occurs.
indicator
indicator
Hold SET appears on the digital display. ➝ HT fl ashes. ➝ Second
•
hand points to the current Home City code.
2. Use A to select the city code you want to select as your Home City.
Each press of A moves the second hand clockwise. Keep pressing
•
A until the second hand is pointed to the city code you want to
select.
•
Select your Home City code before changing any other setting.
•
For full information about city codes, see the "City Code Table" at the
Second
Second
Hour :
Hour :
back of this manual.
Minutes
Minutes
hand
hand
City code
City code
Barometer/
Barometer/
Altimeter Mode
Altimeter Mode
Barometric Pressure Graph
Barometric
Month Day
pressure graph
E-25
E-27
E-29
E-31