Table of Contents
Advertisement
System Setup
System Setup Operation
The Parking Brake must be engaged to access the System
mode screen. Attempting to access this screen while driving
will display the warning-CAN'T OPERATE WHILE DRIVING.
The following steps 1 to 4 are common operations to each
"Setting item" of System Setup. Refer to each section for
details.
1
Press and hold SETUP for at least 2 seconds.
The SETUP selection screen is displayed.
2
Touch [
] of System Setup.
The SYSTEM SETUP screen appears.
3
Touch [ ], [ ] or [
change its setting.
Setting items:
1
IN Int. Mute
*
/ IN Int. Icon / Remote Sensor
3
Camera Signal
*
/ NAV. IN / NAV. Mix
Bluetooth IN / USB Adapter / AUX+ IN / AUX+ Level
1
*
Displayed only when Bluetooth IN is OFF.
2
*
When ON is set in "Setting the Picture Output" (page 19), the item is
displayed.
3
*
Not displayed when OFF is set in "Setting the Rear Camera Input"
(page 18).
4
*
When ON is set in "Setting the Navigation Mode" (page 19), the item
is displayed.
5
*
Not displayed when OFF is set in "Setting the AUX+ Mode"
(page 20).
4
Touch [ ] to return to the previous screen.
Touch and hold [ ] for at least 2 seconds to return to the
main source screen that was displayed before the setup
operation was started.
• Immediately after changing the settings of System Mode (while the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF. Otherwise, the settings may not be changed.
Setting the External Device Interrupt Mode
If an Alpine Ai-NET Interrupt Box (NVE-K200) is connected to this
unit, an Auxiliary Source will be allowed to interrupt the current audio
source. For example, you can listen to the voice guidance of your
navigation system when it occurs even while you are playing a song
stored in the USB memory. The song will be automatically muted
during voice guidance. For further details, please refer to the manual for
NVE-K200.
Setting item: IN Int. Mute
Setting contents: OFF / ON
OFF: The volume level can be adjusted in Interrupt mode.
ON:
Sound will not be output. The icon that is set in "Setting
the Interrupt Icon Display" is displayed.
• The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.
18
-EN
] etc., of the desired item to
2
*
/ Camera IN /
4
*
/ AUX IN / AUX OUT /
5
*
Setting the Interrupt Icon Display
The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN Int. Icon
Setting contents: INT / TEL
INT:
The INT icon appears on the display.
TEL: When the external device (telephone) sends the interrupt
signal, the telephone icon appears on the display.
Switching the function of the remote
sensor
For optional remote control operation, the remote sensor of the external
device (monitor, etc.) can be switched, as you prefer.
Setting item: Remote Sensor
Setting contents: FRONT / REAR
FRONT:
The remote sensor of this unit is effective.
REAR:
The remote sensor of the external monitor
connected to AUX OUT of this unit becomes
effective. The remote control operates the
source connected to the AUX OUT terminals.
• If a touch screen monitor (connected to the Rear Monitor output
using the Monitor control lead) is touched, the command is executed
regardless of the remote control sensor setting. Note, however, that
the remote control sensor that has been set takes priority if it has
been 5 seconds since last touching the panel.
• When an optional DVD changer is connected, and the remote control
sensor is set to REAR, some soft button operations
( [
] STOP, etc.) cannot be performed. In this case, set the remote
control sensor to FRONT.
Setting the Rear Camera Input
With a rear camera connected, rear view video is output to the monitor.
Setting item: Camera IN
Setting contents: OFF / DIRECT / RCA
OFF:
The Camera mode is not displayed in the mode
switching screen.
DIRECT:
Use when the optional rearview camera
HCE-C107D is connected.
RCA:
Use when connecting an optional rearview camera
with RCA output connector.
• By shifting to reverse (R), the rear pictures are output.
This function is effective when the reverse wire is properly connected.
Setting the Rear Camera Signal Input
After setting to RCA or DIRECT in "Setting the Rear Camera Input",
this setting can be carried out.
Setting item: Camera Signal
Setting contents: AUTO / NTSC/PAL
AUTO:
The suitable video input signal type will be
automatically chosen between NTSC and PAL.
NTSC/PAL: Choose the video input signal type manually.
• When set to AUTO, unstable display may occur while playing back
certain black and white video signal. In this case, select NTSC or
PAL mode manually.
Advertisement
Table of Contents
