Table of Contents
Advertisement
Available languages
Available languages
WaRNING: To ReDuce THe RISK oF FIRe, eLecTRIc SHocK, oR INJuRy To peRSoNS,
oBSeRve THe FoLLoWING: ReaD aND Save THeSe INSTRucTIoNS
1.
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999),
including fire-rated construction.
2.
Use this unit only in the manner intended by the manufacturer . If you have any questions contact the manufacturer .
3.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side
of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and
pushed carefully up into the outlet box.
4.
WaRNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
5.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
6.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
7.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to
the trailing edge of the blade.
8.
WaRNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting
screws provided with the outlet box (Mounting must support at least 35 lbs.)
9.
WaRNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor , balancing or during cleaning. Do not insert for-
eign object between rotating blades.
10.
Attach the mounting bracket using only the hardware supplied with the outlet box.
11.
WaRNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
12.
WaRNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manu-
factured by Rhine Electronic Co., Ltd. Suitable for use with solid-state speed controls.
13.
NEVER place a switch where it can be reached from a tub or shower .
14.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit's operation. Follow the heating equipment man-
ufacturer's guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
15.
cauTIoN: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
16.
All set screws must be checked and tightened where necessary before installation.
Phillips Screwdriver
1
Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.
4
Loosen the 2 set screws in yoke
for downrod to slip into yoke.
Installation
S
T
aFeTy
IpS
TooLS ReQuIReD
Wire Cutters
2
Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support.
(Mounting must support at least 35 lbs.)
5
Remove the keeper pin and cross pin
from downrod, and save for later
use.
Pliers
Step Ladder
6
Canopy
Downrod
Ball
Thread canopy and yoke cover on down-
rod. Thread leadwires and safety cable
through the downrod.
as shown above.
Yoke cover
Follow inserts
Advertisement
Table of Contents
