Table of Contents
Advertisement
Active speaker-system
For your own safety, please read this user manual carefully before you initial start-up.
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions of this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- download the latest version of the user manual from the Internet
INTRODUCTION
Thank you for having chosen an OMNITRONIC speaker-system. If you follow the instructions given in this
manual, we are sure that you will enjoy this device for a long period of time.
Unpack your speaker-system.
SAFETY INSTRUCTIONS
This speaker-system has left our premises in absolutely perfect condition. In order to maintain this condition
and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and
warning notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will
not accept liability for any resulting defects or problems.
Please make sure that there are no obvious transport damages. Should you notice any damages on the
connection panel or on the casing, do not take the speaker-system into operation and immediately consult
your local dealer.
The materials used in this speaker-system are normally flammable. If B1 is required at the install-
ation place, the surface must be treated with an appropriate fire retardant in regular intervals.
USER MANUAL
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
DANGER OF BURNING!
DANGER TO LIFE!
18/30
00029746.DOC, Version 1.3
Advertisement
Table of Contents
Related Manuals for Omnitronic KB-208A
Summary of Contents for Omnitronic KB-208A
-
Page 1: User Manual
- download the latest version of the user manual from the Internet INTRODUCTION Thank you for having chosen an OMNITRONIC speaker-system. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time. -
Page 2: Operating Determinations
A crashing speaker-system can cause deadly accidents. All safety instructions given in this manual must be observed. Before the speaker-system is switched on all faders and volume controls have to be set to "0" or "min" position. CAUTION: Turn the amplifier on last and off first! HEALTH HAZARD! By operating speaker-systems with an amplifier, you can produce excessive sound pressure levels that may lead to permanent hearing loss. -
Page 3: Legal Instructions
Before installing the system, make sure that the installation area can hold a minimum point load of 5 times the system's load (e.g. weight 20 kg - point load 100 kg). DANGER! This speaker system must never be stacked - Danger to Life due to crashing speaker systems! DANGER! This speaker system must never be suspended - Danger to Life due to crashing speaker systems! -
Page 4: Information On Hearing Loss
This is why the entrepreneur has to set up warning signs and provide hearing protectors. The staff has to use these. Please note: OMNITRONIC cannot be made liable for damages caused by incorrect installations and excessive noise levels! Information on hearing loss More and more young people suffer from hearing loss of 25 decibel or more, mainly caused by loud music from portable cassette recorders and CD players or discotheques. -
Page 5: Installation
Line In The Line In can either be connected via the RCA-sockets (KB-208A) or the balanced XLR mounting-socket. Line Out Connect the Line output via the balanced XLR-plug (except KB-208A). The connection with the next active speaker should be made via a microphone cable. - Page 6 Before installing the system, make sure that the installation area can hold a minimum point load of 5 times the system‘s load (e.g. weight 20 kg – point load 100 kg). The speaker-system must never be installed higher than 100 cm without secondary attachment. Install the desired number of speaker-systems in the room.
- Page 7 24/30 00029746.DOC, Version 1.3...
-
Page 8: Satellite-Systems
Satellite-systems A satellite-system is a system where a speaker-system with flange is installed on top of a subwoofer. The satellite system must always provide enough stability. Satellite systems are only allowed if the subwoofer‘s weight is twice as much as the top speaker‘s weight. Further- more, the subwoofer‘s base surface must always be sufficiently dimensioned in relation to the top speaker in order to prevent tilting over. - Page 9 When people are located below the load, all necessary safety measures have to be taken in order to avoid injury. The personnel has to be instructed on the content of the user manual and on the dangers related with operating stands. Depending upon the individual installation spot, all necessary measures against movement and for securing the standing safety have to be created.
-
Page 10: Installation On A Wall-Mounting
Installation on a wall-mounting The speaker-system may only be installed on a wall-mounting if the original speaker-system is equipped with an appropriate flange. Before attaching the speaker-system, make sure that the installation area can hold a minimum point load of 5 times the installation‘s weight (e.g. - Page 11 The earth has to be connected! If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation. The device must only be connected with an electric installation carried out in compliance with the IEC- standards.
-
Page 12: Cleaning And Maintenance
In order to avoid damage, please reduce the volume immediately when distortions can be heard. When speaker-systems are destroyed by overload, the guarantee becomes void. Always check the sound pressure level with a meter in order to keep to the threshold. If you want to switch off the system, switch off the speaker-system first in order to avoid acoustic shocks on the speakers. -
Page 13: Technical Specifications
Step 4: Replace the fuseholder in the housing. If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your dealer. TECHNICAL SPECIFICATIONS KB-208A KB-210A KB-212A KB-215A Power supply:...