Control - Mls Switcher (Mls Rs-232 Port); Control - Lan (Ethernet) - Extron electronics MLC 104 IP Plus Series Setup Manual

Control — MLS Switcher (MLS RS-232 Port)
MLC/IR
A B C
Rear Panel
MLC/IR port
on MLS Switcher
Heat Shrink
Over Ground
or Drain Wires
NOTES:
• You must connect a ground wire
between the MLC and MLS.
• If you use cable that has a drain wire,
tie the drain wire to ground at both ends.
Ground ( )
B Receive (Rx) Transmit (Tx)
A Receive (Rx)
Transmit (Tx)
MLC
Right
Side
A A A B B B C C C
Panel
COMM LINK COMM LINK
Select RS-232 protocol via software or SIS
command. Signals are bidirectional, ±5 V.
RS-232 default protocol:
• 9600 baud • 8 data bits
• no parity
Control — LAN (Ethernet)
MAC Address
MAC: 00-05-A6-XX-XX-XX
S/N:
(on top, and
on front panel)
Tx Tx
Rx Rx
GROUND GROUND
IR OUT IR OUT
+V OUT +V OUT
GROUND GROUND
CM CM
IR IN IR IN
SCP SCP
GROUND GROUND
Rx Rx
Tx Tx
GROUND GROUND
GROUND GROUND
+12V IN +12V IN
Right Panel
PC
TCP/IP
Network
B
A
PRESS TAB WITH PRESS TAB WITH
TWEEKER TO REMOVE TWEEKER TO REMOVE
1 1 2 2 3 3
A B
D D D E E E DIGITAL DIGITAL DIGITAL MLS POWER POWER POWER
I/O I/O RS-232 12V 12V
MLS Switcher RS-232 Port
• 1 stop bit
• no flow control
Activity LED:
Blinks to indicate data
is being sent or received.
Link LED: Lights to indicate
a network connection.
LAN
Pins:
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Power
Power Input
• Connect to 12 VDC, 1 A power supply.
• Check the polarity of the power supply
wires before connecting it to the MLC.
• Front panel buttons light when the
MLC receives power.
PRESS TAB WITH PRESS TAB WITH
TWEEKER TO REMOVE TWEEKER TO REMOVE
1 1 2 2 3 3
A A B B
D D D E E E DIGITAL DIGITAL DIGITAL MLS MLS MLS POWER
LINK LINK I/O I/O RS-232 RS-232 12V
Right
Side
Panel
Ethernet (LAN)
Connect to an Ethernet network with a
straight through cable. This port must be
configured.
Default protocol:
• MLC IP address: 192.168.254.254
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.0.0
• DHCP: off
• Link speed and duplex level: autodetected
Straight-through Cable
(for connection to a switch, hub, or router)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-orange
2 orange 2 orange
3 white-green 3 white-green
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 green
7 white-brown 7 white-brown
8 brown 8 brown
Both ends use the TIA/EIA T568A wiring standard.
Ground 12 VDC
(ridged)
(smooth)
Ground ( )
+12 VDC Input
External
Power Supply
(12 VDC, 1 A max.)
Ground all devices.
NOTE: You must use this LAN port
to set up the MLC and
upload GC configuration
files and firmware. All
configuration can be
performed via this port.
Crossover Cable
(for direct connection to a PC)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-green
2 orange 2 green
3 white-green 3 white-orange
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 orange
7 white-brown 7 white-brown
8 brown 8 brown
Wire end 1 following the TIA/EIA T568A wiring standard,
wire end 2 with the T568B wiring standard.
3/16"
(5 mm)
Max.
3