Page 2
’ ’ Directions Be careful not to cause any physical damage by dropping or throwing Veilux VVIP-2L316. Especially keep the device out of reach from children. Do not disassemble Veilux VVIP-2L316. No After Service is assumed when disassembled. Use only the power adapter provided with Veilux VVIP-2L316.
Page 3
Revision History Date Revision Details 2009-08-18 First manual revision creation. 2010-04-19 Addition of windows vista and 7 in trouble shooting Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
It enables real time transmission of synchronized video of up to 2 M pixels and audio data. Remote clients can connect to Veilux VVIP-2L316 for the real time video/audio data through various client solutions running on PC, PDA or mobile phones. Real time 2-way communication is available through bidirectional audio communication feature.
3 zones Arbitrary shape with independent sensitivity Upgrade Firmware upgrade over IP network Administration Remote administration over IP network Web Viewer Simple viewing over internet explorer Client & Viewer NVR-Pro Standard CMS software Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Page 7
’ ’ 3rd Party CMS Ask Veilux for details Dynamic IP support DDNS support Supported Video/Audio stream encryption ID and Password protection Security IP filtering for restricting administrative access for audio and bi-audio Sync to PC Synchronize to PC Time management...
2. Product Description 2.1. Contents The product package contains followings : Contents Description Remarks Veilux VVIP-2L316 IP camera Veilux VVIP-2L316 main unit Default built in standard PoE module 12VDC Adaptor Power Adaptor (IEEE802.3af) (Optional item) Basic tools and hardware Screws, Rubber rings, Mount cap,...
’ ’ 2.2. Product Preview CMS Software Veilux VVIP-2L316 IP-Installer (NVXR-64) PC software to view and record the A/V streaming data transmitted Vandal Proof (Megapixel) PC software to allocate an IP from IP camera. Mini Dome IP Camera address to the IP Camera...
Page 14
’ ’ Figure 2-6. Adjustment knobs for the Camera Figure 2-7. 3 axis based camera position control (Manual adjustment of Pan, Tilt and Video rotation.) Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). 2 LEDs on the Ethernet connector shows the status of Veilux VVIP-2L316 as the followings: Status LED (Dual Color - Red/Green) : It will be lit in green or red depending on the status.
Page 16
TxD (RxD (Connect to RxD of the other end)) For debugging & factory use only. Ground of RS-232C Alarm In/Out and Audio In/Out Used for connecting alarm sensor, alarm annunciation device, microphone and speaker to Veilux VVIP- 2L316. Description LINE OUT (+) 1 V p-p audio signal output for amplified speaker.
Page 17
A switch provided for returning the IP camera to factory default state. Open the dome cover to access the switch. Press the switch for a few seconds while power is applied. Figure 2-10. Factory Default Switch Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
’ 2.5. Accessories for installation Figure 2-11. Accessories for installation of Veilux VVIP-2L316. Silica gel at the right is packaged in a vacuum sealed PVC bag. Figure 2-12. Before placing the Dome Cover, remove the silica gel from the PVC bag and install it as shown in the figure for dehumidification.
Page 19
It is recommended to use the Cable gland for achieving water tight cabling. Refer to the below. Component Body Rubber Installation LAN Cable Figure 2-13. Cable gland for water tight cabling Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Dome Cover. 2. Connect the cables. 3. Adjust the position of the lens for desired viewing of the site. 4. Adjust the focus and zoom. 5. Place the Dome Cover. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Dome Cover. 4. Connect the cables. 5. Adjust the position of the lens for desired viewing of the site. 6. Adjust the focus and zoom. 7. Place the Dome Cover. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Dome Cover. 4. Connect the cables. 5. Adjust the position of the lens for desired viewing of the site. 6. Adjust the focus and zoom. 7. Place the Dome Cover. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
3. Place “In Ceiling Plate” on top surface of the ceiling panel. 4. Slide in “In Ceiling Housing” through the hole and assemble “In Ceiling Plate” and “In ceiling Housing” using screws. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Page 24
6. Connect the wires and finish pipe works. 7. Adjust the manual Pan/Tilt/Video rotation for desired viewing of the site. 8. Adjust the focus and zoom. 9. Place the Dome Cover 10. Sit the “Decoration Ring” to finish. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Starting operation in low temperature If Veilux VVIP-2L316 is powered up under low temperature environment, the internal heater will warm up the product until the temperature inside the product reach at proper operational temperature. The table below shows time required for the heater to warm up the product.
Brief information for first time operation Veilux VVIP-2L316 is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from Veilux VVIP-2L316 can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below: Recommended Remark...
Veilux VVIP-2L316 to the network using one of the following ways. If your LAN Switch does not support standard PoE, connect Veilux VVIP-2L316 as shown in dotted line in Figure 4-1. The DC power is applied through DC adaptor. DC adaptor...
Page 28
Check at the box and fill the empty field with mgmt.net-video.net in ⑦ . Register the IP camera on DDNS. Visit http://www.net-video.net for the registration. If you don’t have an account on www.net-video.net, open an account and register the IP camera after login. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Page 29
’ ’ 3. Remote video connection to Veilux VVIP-2L316 1) Connection through Web Viewer Web Viewer offers simplest way of video connection to Veilux VVIP-2L316. For video connection, enter the IP address of Veilux VVIP-2L316 in the URL window of Internet Explorer as: Can be omitted the [e.g.] Port 80...
Page 30
It is needed to enter ID and password of the administrator. Default ID and password are root, admin. It is highly recommended to change the ID and password to prevent illegal access to the IP camera. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by Veilux VVIP-2L316 for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction.
Try connection to the video again. If the problem persists, or refer to other trouble shooting notes. If “Request timed out” message is returned. ( in the figure below), the network connection or network setting is not in normal state. Check the network cable and settings. Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
3) Uncheck “Use UAC to help protect your computer” 2. Privilege Level Control 1) Select “NVXR-64” icon on the desktop 2) Click right mouse button and select “Properties” 3) Check “Privilege Level” in “Compatibility” tab Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Page 34
’ ’ <Windows 7> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
Page 35
’ ’ 2. Privilege Level Control 1) Select “NVXR-64” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)
If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5. Error message Phone # 1-800-510-6528 Website: www.Veilux.net Rev.1.0(August. 2009)