Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AUSTRALIAN MONITOR AMC MIX
Summary of Contents for AUSTRALIAN MONITOR AMC MIX
- Page 1 A M C M I X I NSTALL ATI ON AND OP ERAT ION M AN UAL...
- Page 2 Do not parallel- or series-connect an amplifi er output with any other amplifi er output. Australian Monitor Inc is not Always operate the unit with the AC ground wire connected to the responsible for damage to loudspeakers for any reason.
-
Page 3: Table Of Contents
2 & 3. There is also the facility to add a tone generator card. TR O U B LE SH O OTING & B LO CK D IAGR AM The Australian Monitor AMC-MIX gives the contractor a low cost FU NCTIO NA L NOTES alternative in applications that are price sensitive, but still require &... -
Page 4: Fr O Nt Pa Ne L
F R O N T PA N E L CH 1-3 These control the levels for each channel input. This LED indicates the unit is powered “on”. BASS POWER There is 12dB of cut and boost at 100Hz. This switch switches power on or off from the mains. The up position is on. -
Page 5: B Ack Pa Ne L
R E A R PA N E L CH 1-3 LINE OUTPUT Each channel input section has two inputs: The LINE output is on a balanced XLR connector. The output level is 1V XLR input - This is a balanced microphone input. It has an input into 1k at rated output. -
Page 6: Insta L Latio N
I N S TA L L AT I O N OUTPUT CONNECTIONS TAPE OUTPUT The TAPE output wiring should be kept as short as possible. Typically less LINE OUTPUT than 3m. The LINE output XLR can be used to connect up to 6 booster amplifi ers. INPUT CONNECTIONS Balanced wiring (shielded pair cable) is recommended. -
Page 7: Tr O U B Le Sh O Oting & B Lo Ck D Iagr Am
T R O U B L E S H O O T I N G & B L O C K D I A G R A M TROUB L ESHO OTIN G G UI D E TROUBLE LIKELY CAUSE REMEDY Power LED not on Power not reaching mixer... -
Page 8: Fu Nctio Na L Notes & Inte R Na L A Dj U Stments
F U N C T I O N A L N O T E S & I N T E R N A L A D J U S T M E N T S PRIORITY Channel 1 will mute channels 2 and 3. This will only occur when signal ap- pears on channel 1, irrespective of the channel volume controL. -
Page 9: D Imensio Ns
D I M E N S I O N S A M C - M I X I N S TA L L AT I O N & O P E R AT I O N M A N U A L PA G E 9... -
Page 10: S Pe Cific Atio Ns
S P E C I F I C AT I O N S 20Hz - 20kHz (+0,-3dB) FREQUENCY RESPONSE TOTAL HARMONIC DISTORTION < 0.5% @ 1kHz SIGNAL TO NOISE RATIO > 84dB (all pots at centre position) CROSSTALK > 60dB TONE CONTROL BASS @ 100HZ +/- 12dB... -
Page 11: Note S
N O T E S A M C - M I X I N S TA L L AT I O N & O P E R AT I O N M A N U A L PA G E 1 1... - Page 12 AUSTRALIA AND NEW ZEALAND w w w. a u s t r a l i a n m o n i t o r. c o m . a u SYDNEY MELBOURNE BRISBANE ADELAIDE PERTH AUCKLAND (SA & NT SALES) (NSW &...
Need help?
Do you have a question about the AMC MIX and is the answer not in the manual?
Questions and answers