CTC Union FRM220-10 User Manual

Introduction
The FRM220 Family are slide-in-line cards for placement in the FRM220 Platform Media
Converter Chassis and available in a number of different models that also act as a stand-alone
converter for placement in one-slot chassis. The FRM220-10/100I is a media converter for
10Base-T or 100Base-TX, data transmission over optical fiber media depending on your
specific network needs. All media converters are available with either multi-mode or
single-mode optical transceivers and with connectors for SC, ST or FC. In single mode, WDM
(Wave Division Multiplexing with SC connector) is also available in 20, 40, 60, or 80Km reach,
which will provide the ability to transmit and receive data using only a single optical fiber.
When the FRM220-10/100I card is placed in the FRM220 rack, the In band management, can
monitor, configure and control the activity of each port for both local or remote sides. For the
UTP side, auto-negotiation is default. You may set data rate to 10Mbps or 100Mbps and
duplex mode to full or half duplex. The Fiber Transceiver Converters give you the freedom to
extend your 10/100Mbps cabling distance by allowing connectivity up to 120 kilometers. Six
LED indicators signal the power status of the converter, UTP port speed, duplex status and
Link/Act and FX port Link/Act and FEF (Far End Fault).
Features
■
Auto Negotiation or Manual mode in TP port
■
Link fault pass through (LFP) function
■
Forward 2046 bytes packets in switch mode
■
Forward 9K jumbo packets in Pass through mode
■
Compatible with FRM220 Chassis In Band Management :
■
Bandwidth control (32K or 512Kbps x N)
■
Supports local or remote Monitor (Link/Speed/Duplex/Power)
■
Supports local or remote Configure
(Speed/Duplex/port disable/Operating mode/bandwidth)
■
Supports remote CPE power fail detect ( dying gasp )
■
Provides Auto Laser Shutdown (ALS) function
■
Supports On-Line F/W upgrade (local or remote)
s a l e s @ c t c u . c o m
Panel
■ Figure #1. Front Panel of FRM220-10/100I(S)
■ Figure #2. Rear Panel of Stand-alone FRM220-10/100I(S)-DC12
FRM220-10/100I(S)-AC/DC48/AD/AD-M
AC Jack
Power
Switch
DC Jack
10/100I-DC12 10/100I-AC
s a l e s @ c t c u . c o m
w w w . c t c u . c o m
AC Jack
Power
Switch
Power Power
Switch Switch
DC DC
Terminal Terminal
10/100I-DC48 10/100I-AD
10/100I-AD-M
w w w . c t c u . c o m

User Guide

In-band Managed Fiber Media Converter
10/100Base-TX / 100Base-FX – FRM220-10/100I
Specifications
Standards
IEEE802.3 10BASE-T, IEEE802.3u 100BASE-TX, l00BASE-FX (Fast Fiber, 100Mbps)
Supports Full Duplex Ethernet mode (200Mbps)
FRM220-10/100 family supports transmission of Ethernet packet up to 2046Bytes in size.
Fiber
Connections
10/100BASE-TX RJ-45 Connectors
LEDs
One RJ-45 connector is provided for connection to MDI-X (To PC) or MDI (To HUB) equipment.
Auto MDI-X allows all UTP connections to be made using only a common straight-through
Ethernet
Connections UTP cable.
100BASE-TX UTP Cable
Cable type: 100Base-Tx; Category 5 or better
Maximum cable distance: 100 meters (328 feet)
Fiber Optic Connectors
FRM220-10/100I : SC connectors are provided for optic cable connection.
FRM220-10/100IS : one SFP slot with LC connectors is provided for optic cable connection
Environment
Operating -- 0°C – 50°C, Storage -- 0°C – 70°C,
Humidity -- 10 – 90%, (non-condensing)
Power
Adapter: 12V DC 1A, Built-in AC Power 100~240 V, Built-in DC Power 18~72VDC
Dimensions: (W x D x H) mm
10/100I(S)-DC12 : 88 × 160 × 24
10/100I(S)-DC48 : 135 × 201 × 35
10/100I(S)-AD-M : 135 × 201 × 35
s a l e s @ c t c u . c o m
CTC Union Technologies Co., Ltd.
w w w . c t
s a l e s @ c t c u . c o m
RJ-45 Pin MDI-X type
1 Rx+
2 Rx-
3 Tx+
6 Tx-
10/100I(S)-AC: 135 × 201 × 35
10/100I(S)-AD: 135 × 201 × 35
c u . c o m
MDI type
Tx+
Tx -
Rx+
Rx -
w w w . c t c u . c o m