To Delete All Saved Data; To Delete A Specifi C Record - Casio 3410 Operation Manual

Records
Time
Month - Day
Hour,
minute,
second
Barometer/Thermometer
Temperature
(alternating with
month, day)
Barometric
pressure
(alternating
with hour,
minute)
E-72

To delete all saved data

Important!
• A delete operation cannot be undone! Make sure you do not need data before you delete it.
In the Data Recall Mode, hold down E for at least fi ve seconds. Hold will fl ash on the display fi rst for
about two seconds and then disappear. Keep E depressed. Hold will start fl ashing again and then it will
disappear after about fi ve seconds. Release E at this time. - - - - will appear on the display to indicate
that all the data was deleted.
To delete a specifi c record
Important!
• A delete operation cannot be undone! Make sure you do not need data before you delete it.
1. In the Data Recall Mode, use A and C to scroll through records in watch memory until the one you
want to delete is displayed.
2. Hold down E for at least two seconds. First, CLEAR Hold will fl ash in the display. After that, Hold will
disappear. Release E when Hold disappears.
CAUTION!
Holding down E for more than about fi ve seconds will delete all data currently in watch memory.
•
E-74
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use A (East) and C (West) to scroll through
the available city codes.
• Keep scrolling until the city code whose Standard Time/Daylight
Saving Time setting you want to change is displayed.
2. Hold down E for at least two seconds. DST and Hold will appear on
the display fi rst, and then Hold will disappear. Release E after Hold
disappears.
• This will toggle summer time between on and off.
• The DST indicator is displayed while summer time is turned on.
• Using the World Time Mode to change the DST setting of the
city code that is selected as your Home City also will change the
Timekeeping Mode time DST setting.
• Note that you cannot switch between standard time/daylight
saving time (DST) while UTC is selected as the World Time City.
• Note that the standard time/daylight saving time (DST) setting
affects only the currently selected city. Other cities are not
affected.
DST indicator DST indicator
E-76
To measure two fi nishes
A C
Start Split
First runner fi nishes.
(SPLIT appears in
the upper part of the
display.)
Display time of fi rst
runner
Note
• The Stopwatch Mode can indicate elapsed time up to 999 hours, 59 minutes, 59.99 seconds.
Once started, stopwatch timing continues until you press A to stop it, even if you exit the Stopwatch
•
Mode to another mode and even if timing reaches the stopwatch limit defi ned above. A paused timing
operation will remain paused until you press A to resume it or C to reset.
• Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns
to elapsed time measurement.
• While SPLIT is shown in the display, it alternates with the hour digits of the split time at one-second
intervals.
You can directly access the Stopwatch Mode from the Timekeeping Mode by pressing the A button. If
•
the stopwatch is reset to all zeros when you enter the Stopwatch mode, the watch will beep twice and
an elapsed time operation will start automatically. You can check whether the stopwatch is reset by
looking at the Timekeeping Mode graphic (page E-29).
E-78
Operation Guide 3410
Bearing
Hour, minute
(alternating with
month, day)
Bearing
Altitude
Time (alternates
with date)
Altitude
A C
Stop Split release
Second runner Display time of
fi nishes. second runner
Historical Altitude Values
High Altitude
High
Altitude
Total Ascent
Total
Ascent
* During display of the cumulative ascent or cumulative descent value, shows the
cumulation start date.
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 31 time zones (48 cities) around the
globe. The city that is currently selected in the World Time Mode is called the "World Time City".
To enter the World Time Mode
Use D to select the World Time Mode (WT) as shown on page E-26.
Time offset graphic
(24-hour indication)
Home City
time
22:58
• After about one second, the city code and name of the currently selected city will scroll across the
display. After that, the city code only will remain on the display.
To view the time in another time zone
In the World Time Mode, use A (East) and C (West) to scroll through city codes.
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
1/10-second 1/10-second Hours Hours
graphic graphic
Current time Current time
Minutes Minutes Seconds Seconds
1/100 second 1/100 second
Using the Countdown Timer
C
The countdown timer can be confi gured to start at a preset time, and sound an alarm when the end of the
countdown is reached.
Reset
Countdown time Countdown time
(Hour, minutes, seconds) (Hour, minutes, seconds)
Minutes Minutes
graphic graphic
Current time Current time
3. Press D to move the fl ashing between the hour and minute settings.
4. Use A (+) and C (–) to change the fl ashing item.
• To set the starting value of the countdown time to 24 hours, set 0H 00'00.
5. Press E to exit the setting screen.
Low Altitude
Hour, minute
(alternating with
month, day)
Low
Altitude
Total Descent
Month, day
(alternating with
year) *
Total
Descent
Currently selected Current timekeeping
Word Time City Mode time
World Time
Current time in the currently
City time
8:58 selected World Time City
To enter the Stopwatch Mode
Use D to select the Stopwatch Mode (STW) as shown on page E-26.
To perform an elapsed time operation
A
A A
Start Stop (Resume)
To pause at a split time
C
A C
Start Split Split release
(SPLIT appears
in the upper part
of the display.)
To enter the Countdown Timer Mode
Use D to select the Countdown Timer Mode (TMR) as shown on page E-26.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting
down), press A to stop it and then press C to reset to the current
countdown start time.
If a countdown is paused, press C to reset to the current
•
countdown start time.
2. Hold down E for at least two seconds.
• SET Hold will fl ash on the display and then the current start time
setting will start to fl ash. Keep E depressed until the start time
setting starts to fl ash.
Hour, minute
(alternating with
month, day)
Month, day
(alternating with
year) *
E-73
E-75
A
C
(Stop) Reset
A
C
Stop Reset
E-77
E-79