Summary of Contents for FieldServer FS-8700-59 Canatal Satchnet
Page 1
Sierra Monitor Company Driver Manual (Supplement to the FieldServer Instruction Manual) FS-8700-59 Canatal Satchnet Driver APPLICABILITY & EFFECTIVITY Effective for all systems manufactured after May 1, 2001 Instruction Manual Part Number FS-8700-59 3/13/03...
The driver can read/write Bit, Byte, Swapped Integer, Word, BCD and Float Data. The Canatal Satchnet Protocol Driver can act as a (passive) server. • The driver can be polled by a Satchnet Master and return data from the FieldServer's data arrays. •...
100 ohms to frequencies greater than 100 kilohertz and a DC series loop resistance not exceeding 240 ohms. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042 Visit our website: www.fieldserver.com E-mail: support@fieldserver.com...
Canatal Satchnet Protocol Driver Server ( a passive Canatal device). The configuration file tells the FieldServer about its interfaces, and the routing of data required. In order to enable the FieldServer for Canatal Satchnet Protocol Driver communications, the driver independent FieldServer buffers need to be declared in the “Data Arrays”...
FLOAT and should have at least 1 element International information or read the in size. Corporation Inc. vendor product literature. Product Literature. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042 Visit our website: www.fieldserver.com E-mail: support@fieldserver.com Page 6...
The offset is added to the address when determining the element of the data array to be used for storage. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042 Visit our website: www.fieldserver.com E-mail: support@fieldserver.com Page 7...
This section documents and describes the parameters necessary for configuring the FieldServer to communicate with a Canatal Satchnet Protocol Driver Client (Master) The configuration file tells the FieldServer about its interfaces, and the routing of data required. In order to enable the FieldServer for Canatal Satchnet Protocol Driver communications, the driver independent FieldServer buffers need to be declared in the “Data Arrays”...
Canatal Handshaking* Specify hardware handshaking RTS, RTS/CTS, None The FieldServer is capable of handling any of the above connection specification but the Canatal Corporation Inc. devices are support the specification provided in the example below. Example Server Side Connections Connections...
Scada_Hold_Timeout Specifies time server side waits before responding to client >1.0s that node is offline on FieldServer client side. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042 Visit our website: www.fieldserver.com E-mail: support@fieldserver.com Page 10...
In this example the FieldServer answers queries from a Canatal Satchnet master device. A same map descriptor could be used when the same master wants to write data to the FieldServer. In this example the FieldServer is emulating a Canatal device addressed as node 11. It is not possible to have the FieldServer emulate two devices of difefrent series addressed as node 11.
Page 15
Note that map descriptors that include a range of points of mixed data formats will cause unexpected results. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042 Visit our website: www.fieldserver.com E-mail: support@fieldserver.com...
Changed request from %u to %u The driver has truncated you data_length so that it does not read/write beyond the end of a table. FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 (408) 262-2299 fax: (408) 262-9042 Visit our website: www.fieldserver.com E-mail: support@fieldserver.com...
Need help?
Do you have a question about the FS-8700-59 Canatal Satchnet and is the answer not in the manual?
Questions and answers