Viper 4205V Owner's Manual page 19

Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
1. Turn the ignition on, then off.
2. Select a Menu. Within 10 seconds, Press and hold the Valet button. The number of LED flashes and horn
honks indicates the menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2
honks indicates menu 2.
When the desired menu LED flashes and honks are heard, release the Valet button.
3.
Select a Feature, within 10 seconds. Press and release the Valet button the number of times correspond-
4.
ing to the feature you wish to change. Then press and hold one more time to select the feature. The LED
flashes and the horn honks to indicate which feature is selected.
5. Program the Feature. While holding the Valet button, you can program the feature using the remote
control.
Pressing the button on the remote control advances to each feature option. The LED flashes and the horn honks
indicating which option is selected.
Once a feature is programmed:
• Other features can be programmed within the same menu
• Another menu can be selected
• The learn routine can be exited if programming is complete
To access another feature in the same menu:
1. Press and release the Valet button the number of times necessary to advance from the feature you just pro-
grammed to the next one you want to program.
2. Then press the Valet button once more and hold it.
To select another menu:
1. Press and hold the Valet button.
2. After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
• The ignition is turned On
• There is no activity for 30 seconds
• The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter® gives you access to a wider range of system options. These additional features and the adjust-
ments that may be programmed are described in the table below.
Menu Item Feature Default
1 Engine Runtime 12 min.
2 Diesel start type Off
3 15 sec
Diesel start delay time (seconds)
4 Virtual Tach Fine Tune Not initialized
5 Remote control programming Unlocked
6 Feature Programming Unlocked
© 2013 Directed. All rights Reserved.
Feature Menus
Default settings are in bold type.
Menu 1
Feature # Feature
1 Horn function
2 Ignition con-
trolled lock
3 Ignition con-
trolled unlock
4 Doorlock out-
put duration
5 Double pulse
unlock
6 Double pulse
lock
7 Factory Alarm
Disarm func-
tion
8 Factory Alarm
Disarm Pulses
9 Comfort*
Closure
10 Panic*
**Option not available on 1- button
Menu 2
Feature # Feature
1 Engine check-
ing
2 Engine
Runtime
3 Park light
output
4 Cranking time
5 Activation
pulse count
6 2nd Ignition
behavior
7 Accessory
Options
output
8 2nd Status
1-60 min.
behavior
Timed
9 Anti-grind
1-90 sec.
0 to 1 second in 50 millisecond
10 Diesel start
increments
delay
Locked
11 Timer mode-
Locked run time *
*Option not available on 1- button
Opt. 1 Opt. 2 Opt. 3 Opt.4
Off Siren Siren Siren
20 mS 30 mS 40 mS
On Off
On Off
0.8 sec. 3.5 sec. 0.4 sec.
Off On
Off On
with unlock Before unlock Remote start
only
Single Double
Comfort Off Comfort
Closure 1 Closure 2
On Off
Opt. 1 Opt. 2 Opt. 3 Opt.4
Virtual tach voltage Off tachometer
12 min
24 min 60 min
Pulsed Constant
0.6 sec. 0.8 sec. 1.0 sec. 1.2 sec.
1 pulse 2 pulses 3 pulses
Ignition Accessory
Off during On during
wait-to-start wait-to-start
Normal Latch rear Pulse rear
defogger defogger
On Off
Off Timed 15 sec Timed 30 sec. Timed 45 sec.
12 min 3 min 6 min 9 min
Remote Programming
1. Turn key to the ON position
2. Within 10 seconds, press and release Valet button one time.
3. Within 10 seconds, press and hold the Valet button. The LED will flash one time and the horn honks (if con-
nected) to confirm entry into remote programming.
4. Press the button on the remote control.
Opt. 5+
5. The horn honks to confirm the remote has been programmed.
6. Release the Valet button, and turn the key to the Off position.
Siren
7. The horn sounds one long honk to confirm that remote programming has been exited.
50 mS
The programming routine exits if any of the following occurs:
• The ignition is turned off
• There is no activity for 30 seconds
• The Valet button is pressed too many times
Basic Remote Functions
Button Press Function when remote
start is OFF
Press for less than 1.5 Start the engine
seconds
Press for more than 1.5 Car finder
seconds
Opt. 5+
1.4,
1.6,
1.8,
2.0,
4.0 sec
See full Installation Guide for more
detailed information on this system.
Such information and more can be
found online at:
www.directechs.com
Function when remote
start is ON
Unlock doors
Stop the engine
QRN4205 2013-06
2