CDA Oven Manual To Installation page 8

EN 2 / INSTALLING YOUR APPLIANCE
Warning
W W e e c c a a n n n n o o t t b b e e h h e e l l d d r r e e s s p p o o n n s s i i b b l l e e f f o o r r a a n n y y a a c c c c i i d d e e n n t t r r e e s s u u l l t t i i n n g g f f r r o o m m a a n n i i n n e e x x i i s s t t e e n n t t , , d d e e f f e e c c t t i i v v e e
o o r r i i n n c c o o r r r r e e c c t t g g r r o o u u n n d d l l e e a a d d . .
I I f f t t h h e e e e l l e e c c t t r r i i c c a a l l i i n n s s t t a a l l l l a a t t i i o o n n a a t t y y o o u u r r r r e e s s i i d d e e n n c c e e r r e e q q u u i i r r e e s s a a n n y y c c h h a a n n g g e e s s i i n n o o r r d d e e r r t t o o h h o o o o k k u u p p y y o o u u r r
A A p p p p l l i i a a n n c c e e , , c c a a l l l l u u p p o o n n a a p p r r o o f f e e s s s s i i o o n n a a l l e e l l e e c c t t r r i i c c i i a a n n . .
I I f f t t h h e e o o v v e e n n m m a a l l f f u u n n c c t t i i o o n n s s i i n n a a n n y y w w a a y y , , u u n n p p l l u u g g t t h h e e a a p p p p l l i i a a n n c c e e o o r r r r e e m m o o v v e e t t h h e e f f u u s s e e c c o o r r r r e e s s p p o o n n d d i i n n g g
t t o o t t h h e e s s e e c c t t o o r r t t h h e e r r e e t t h h e e o o v v e e n n i i s s h h o o o o k k e e d d u u p p . .
CHANGING THE POWER CORD
• •
— — The power cable (H05 RR-F, H05 RN-F ou H05 VV-F) must be of sufficient length to be connect-
ed to the build-in oven while it sits on the floor in front of the cabinet.
To do this the appliance must be disconnected from the electrical network:
— — Open the inspection flap located at the lower right of the back cover by unscrewing the two
screws, then pivot the inspection flap.
— — Strip 12 mm along each wire of the new power cable.
— — Carefully twist together the strands.
— — Loosen the screws from the terminal board and remove the power cord to be replaced.
• Introduce the power cable through the side of the cover in the cable clip located to the right of
the terminal board.
— — All the strands of the electricity wires must be captured under the screws.
— — The phase wire on the L terminal.
— — The green-yellow coloured ground wire should be connected to the terminal
— — The neutral conductor (blue) on the N terminal.
— — Screw down tightly the screws on the terminal board and check the connection by pulling on each
wire.
— — Attach the cable with the cable clip located to the right of the terminal board.
— — Close the inspection flap using the two screws.
8
.