Alliance Laundry Systems 602004144 Operation And Maintenance Manual
Alliance Laundry Systems 602004144 Operation And Maintenance Manual

Alliance Laundry Systems 602004144 Operation And Maintenance Manual

Stacked 30 pound capacity; stacked 45 pound capacity
Hide thumbs Also See for 602004144:

Advertisement

Tumble Dryers
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Stacked 30 Pound Capacity
Stacked 45 Pound Capacity
Starting Serial No. 0602004144
Refer to Page 3 for Model Numbers
www.comlaundry.com
Part No. 70400101R9EN
July 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 602004144 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Alliance Laundry Systems 602004144

  • Page 1 Tumble Dryers Stacked 30 Pound Capacity Stacked 45 Pound Capacity Starting Serial No. 0602004144 Refer to Page 3 for Model Numbers Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 70400101R9EN July 2011 www.comlaundry.com...
  • Page 3 These instructions must be posted in a prominent location. Step-by-step instructions of the above safety information must be posted in a prominent location near the tumble dryer for customer use. 70400101 (EN) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 4: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 5: Introduction

    SX – single drop, prep for coin 3V – DX4 vended QT – dual digital timer 3X – DX4 prep for coin SD – single drop © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 6: Customer Service

    Model and serial numbers are found on serial plate on the rear of machine and inside door. Refer to Figure 1. TMB1974N Serial Plate Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 7: Safety Information

    NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 8: Important Safety Instructions

    12. Always clean the lint filter daily. gas supply must comply with local codes and be made by licensed personnel when required. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 9 28. DO NOT operate the tumble dryer if it is W055R1 smoking, grinding, has missing or broken parts. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 10: Operating Instructions

    IMPORTANT: Always follow the fabric care instructions supplied by the garment manufacturer. Step 4: Remove Laundry When the cycle is complete, open door and remove the laundry. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 11: Control Instructions

    Start ( ) pad must be pressed. 3. When the cycle is complete, open door and remove laundry. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 12: Dual Digital Timer Control

    3. Set the COOL DOWN TIME for the number of minutes (from 0-15) desired. 4. Press and release START button to start tumble dryer. Display will show minutes remaining before end of cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 13 Anti-wrinkle feature will tumble the load without heat for 30 seconds every 2 minutes for 1 hour OR until the loading door is opened. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 14: Error Codes

    • Allow up to 20 seconds for this condition to clear. Airflow Switch Closed when Resuming Cycle • Check if airflow switch opens at end of cycle. (Solid) • Replace airflow switch if inoperative. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 15: Single Drop Control

    18 hours or until door is In Run Mode, the control is running a cycle. The IN opened. USE LED is lit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 16 W002R1 Display Definition Corrective Action • Airflow switch opened/closed 5 or more Check airflow switch. Replace if inoperative. AF (Flashing) times in a running cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 17: Dx4 Coin Control

    Cool Down Time Left Button 104°F (40°C) Varies 2 min. Middle Button 140°F (60°C) Varies 2 min. Right Button 176°F (80°C) Varies 2 min. Table 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 18: Dx4 Opl Control

    Left Button 104°F (40°C) 30 min. 2 min. Middle Button 140°F (60°C) 30 min. 2 min. Right Button 176°F (80°C) 35 min. 2 min. Table 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 19: Ignition Control Operation For Non-Ce Models

    When this occurs, the control must complete the same prepurge and ignition sequence specified above. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 20: Ignition Control Operation For Ce Models

    Lockout Mode again. before the ignition control makes another attempt at ignition. If the three attempts at ignition fail, the ignition control will enter Lockout Mode. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 21 Reset Switch is Shorted Slow Red and Green Flashes Low Voltage Detection Fast Red and Orange Flashes Ignition Control is in Reset Delay TMB2176N Diagnostic (DGN) LED Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 22: Maintenance

    Lightly brush any lint that may be left on the lint screen. Lint left in the lint compartment is drawn back onto the lint screen and will restrict airflow. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 23 • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the tumble dryer is properly grounded. W002R1 TMB2116N TMB2116N Blower Housing Cabinet Thermostat Thermistor Guard Figure 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 24: Monthly

    3. Check and clean steam coils, if applicable. 4. Check flow of combustion and ventilation air. 5. Check belt tension and condition. Replace worn or cracked belts. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 25: Daily Maintenance

    Lint buildup will act as an insulator, causing machine to overheat. Clean lint and debris buildup from blower to maintain proper airflow, avoid overheating and prevent possible vibration. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 26 Check and clean steam coils, if applicable. Check flow of combustion and ventilation air. Check belt tension and condition. Replace worn or cracked belts. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 27 Check seal and idler assembly for wear. Remove burner tubes and clean using water and a brush. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)
  • Page 28: Before You Call For Service

    Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor. For technical assistance, call (920) 748-3121. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400101 (EN)

Table of Contents