Table of Contents
Troubleshooting
Related Manuals for Kenmore 415.16107110
Summary of Contents for Kenmore 415.16107110
- Page 1 Use & Care Guide Model: 415.16107110 Kenmore ® Liquid Propane Gas Grill P/N 307010030 Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A. www.kenmore.com www.sears.com ™ Model 464430111 • Oct-19-10...
-
Page 2: For Your Safety
DANGER WARNING CALIFORNIA PROPOSITION 65 If you smell gas: 1. Combustion by-products produced when using this 1. Shut off gas to the appliance. product contain chemicals known to the State of 2. Extinguish any open flame. California to cause cancer, birth defects, and other reproductive harm. -
Page 3: Table Of Contents
1-800-4-MY-HOME to arrange for free repair (or Kenmore Grill Warranty......3 replacement if repair proves impossible). -
Page 4: Use And Care
LP Tank USE AND CARE • The LP Tank used with your grill must meet the following requirements: DANGER • Use LP Tanks only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. - Page 5 LP Tank Exchange Connecting Regulator To The LP Tank • Many retailers that sell grills offer you the option of 1. LP tank must be properly secured onto grill. (Refer to replacing your empty LP tank through an exchange service. assembly section.) Use only those reputable exchange companies that inspect, precision fill, test and certify their tanks.
- Page 6 Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP tank. 3. Completely open LP tank valve by turning OPD hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately.
- Page 7 Safety Tips WARNING Before opening LP cylinder valve, check the coupling nut for tightness. When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious Never move grill while in operation or still hot. Injury: Use long-handled barbecue utensils and oven mitts to •...
- Page 8 Burner Flame Check WARNING • Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW. You should see a smaller flame in LOW position than seen on HI. Perform burner Turn controls and gas source or tank OFF when not flame check on sideburner, also.
-
Page 9: Spider Alert
3. Remove carryover tubes and burners. CAUTION 4. Detach electrode from burner. NOTE: Removal/Detachment method will depend on the burner configuration. See different configurations in illustrations below. SPIDER ALERT! 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. - Page 10 Indirect Cooking Food Safety Poultry and large cuts of meat cook slowly to perfection on Food safety is a very important part of enjoying the the grill by indirect heat. Place food over unlit burner(s); the outdoor cooking experience. To keep food safe from heat from lit burners circulates gently throughout the grill, harmful bacteria, follow these four basic steps: cooking meat or poultry without the touch of a direct flame.
-
Page 11: Parts List
PARTS LIST Key Qty Description Part # Key Qty Description Part # LEFT FRONT LEG SH20705006-2 CONTROL KNOB 302230012 LEFT REAR LEG SH20705006-4 LEFT FASCIA 205040005 LEG EXTENDER LEFT SIDE SHELF 302470076 20704006-2 RIGHT FRONT LEG SH20705006-3 TOWEL BAR 205050001 RIGHT REAR LEG SH20705006-5 END CAP, F/ TOWEL BAR, RF/LR... -
Page 12: Parts Diagram
PARTS DIAGRAM 12 · 464430111... -
Page 13: Assembly
ASSEMBLY Bottom Shelf and Legs □ Attach legs to bottom shelf with 1/4-20x2-3/8” machine screws. Be sure that metal tabs on legs face to cart interior as shown. Left Rear Leg Left Front Leg Metal Tabs Metal Tabs Right Rear Leg Right Front Leg Bottom Shelf 1/4-20x2-3/8”... - Page 14 Side Braces □ Turn cart upright. □ Attach side braces to legs using four 1/4-20x1/2” screws each side. 1/4-20x1/2” Side Brace Machine Screws Qty. 8 Side Brace Front Panels □ Fit one front panel between front legs and attach with two 5/32-32x3/8” machine screws each side. Then attach the front panel to bottom shelf with two 5/32-32x3/8”machine screws.
- Page 15 Tank Exclusion Brace □ Insert the end without hole into the left slot in the front panels, and then use one 5/32-32x3/8” machine screw to attach tank exclusion brace to bottom shelf. 5/32-32x3/8” Machine Screws Qty. 1 Tank Exclusion Brace Back Brace □...
- Page 16 Tank Heat Shield □ Use four 5/32-32x3/8" machine screws to attach tank heat shield to back brace on one side. Attach other side under lip of upper front panel as shown. 5/32-32x3/8” Machine Screws Qty. 4 Tank Heat Shield Grill Head □...
- Page 17 Side Shelf and Fascias □ Use three 5/32-32x3/8” machine screws to attach fascia to left side shelf as shown (A). □ Remove grate from beneath lid of sideburner shelf. Use three 5/32-32x3/8” machine screws to attach fascia to sideburner shelf as shown (B). Left Fascia 5/32-32x3/8”...
- Page 18 Left Side Shelf □ Loosen the preassembled screws in the left rear leg and front of firebox, shown A, to within 1/8" of surface. Hang left side shelf onto the screws through the keyhole slots in the shelf. Fully tighten all screws.
- Page 19 SideBurner Shelf □ Loosen the preassembled screws in the right rear leg and front of firebox, shown A, to within 1/8" of surface. Hang sideburner shelf onto the screws through the keyhole slots in the shelf. Fully tighten all screws. □...
- Page 20 Side Burner Valve and Bezel □ Remove the two screws, shown A, preassembled to the sideburner valve. □ Insert the sideburner valve control stem through the fascia and sideburner bezel, shown A. Use the two previously removed screws to attach sideburner valve to fascia and bezel. □...
- Page 21 Sideburner Knob □ Use supplied Allen wrench to loosen set screw in control knob. Push knob onto valve stem. Tighten set screw. Sideburner Knob Side Burner Ignitor Wire 4 14 □ Insert the socket pin of sideburner electrode wire into harness of ignitor wire as shown below. Sideburner Electrode Wire Ignitor Wire...
- Page 22 Grease Tray and Grease Pan □ Slide grease tray onto rails beneath firebox past rail stops. Slide grease pan onto rails beneath grease tray past rail stops. CAUTION Failure to install grease tray and pan will cause hot grease to drip from bottom of grill with risk of fire or property damage.
- Page 23 Install Grates, Warming Rack and Battery □ Insert cooking grates into firebox. To obtain sear marks in cooked meat, be sure to insert grates so that side with four corner feet faces down. Install warming rack into firebox with legs inserted into sidewall holes as shown.
-
Page 24: Troubleshooting
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Possible Cause Prevention/Solution Gas leaking from • Damaged hose. • Turn off gas at LP cylinder or at source on natural gas systems. cracked/cut/burned If the hose is cracked or cut but not burned, simply replace hose. - Page 25 Troubleshooting (continued) Problem Possible Cause Prevention/Solution Burner(s) will not light ELECTRONIC IGNITION: using ignitor. • No spark, no ignition noise. • See Section I of Electronic Ignition System. (See Electronic Ignition Troubleshooting also) • No spark, some ignition noise. • See Section II of Electronic Ignition System. •...
-
Page 26: Troubleshooting
Troubleshooting - Electronic Ignition Problem (Ignition) Possible Cause Check Procedure Prevention/Solution SECTION I No sparks appear at • Battery not installed • Check battery orientation. • Install battery (make sure that “+” and “–” properly. connectors are oriented correctly, with “+” end up any electrodes when Electronic Ignition and “–”... - Page 27 NOTES 464430111 • 27...