Condensate Drain Lines - Amana GUCA045AX30 Service Instructions Manual

HOSE
A
FRONT COVER
DRAIN PORT
Upright "Standard" Connections
Right Side
(Upflow Shown, Counterflow Similar)
LEFT
SIDE PANEL
FRONT COVER
DRAIN PORT
HOSE A
SIDE PANEL
GROMMET
HOLES
TUBE(S) 2
DRAIN
TRAP
Upright "Standard" Connections
Left Side
(Upflow Shown, Counterflow Similar)
3. Cut and remove 1/4 inch from the end of the drain port
on the rubber elbow.
4. Insert Tube 1 into rubber elbow drain port and secure
with hose clamp. Angle tube outward toward front of
furnace.
5. Right side drains
Cut 17 3/4 inches from the long end of Hose B and
discard. Secure the remaining hose to Tube 1 with a
hose clamp. Route the other end of Hose B to front
right side panel grommet hole.
Left side drains
Cut "X" inches from the long end of Hose B and dis-
card. Refer to table for appropriate length to cut. Se-
cure remaining hose to Tube 1 with a hose clamp. Route
other end of Hose B to front left side panel grommet
hole.
30
Rev. 0

CONDENSATE DRAIN LINES

AND DRAIN TRAP
RIGHT SIDE
PANEL
RUBBER
ELBOW
RUBBER ELBOW
DRAIN PORT
TUBE 1
HOSE B
SIDE PANEL
GROMMET
HOLES
TUBE(S) 2
DRAIN
HOSE
TRAP
CLAMPS
(5 PLACES)
RUBBER
ELBOW
RUBBER
ELBOW
DRAIN PORT
TUBE 1
HOSE
CLAMPS
(5 PLACES)
HOSE B
Model
Cabinet Width
GUCA & GCCA
(inches)
(kBTU Tons)
045__30
16.5
070__30
070__40
20.5
090__40
090__50
24.5
115__50
6. Insert short end of each Tube 2 through side panel grom-
met holes. Secure tubes to Hose A and Hose B with
hose clamps.
Note: Ensure hoses and tubes maintain a downward slope
for proper drainage and that they are not kinked or binding.
For details concerning mounting of the drain trap, refer to ,
Condensate Drain Lines and Drain Trap - Upright Drain
Trap Mounting section.
Alternate Vent/Flue Drain Hose Connections
Upright installations using the alternate vent/flue outlet will
require "right-side only" drain hoses to be connected as
follows. Refer to Vent/Flue Pipe and Combustion Air Pipe
section for details on alternate vent/flue pipe connection.
1. Remove the rubber plug from the front cover right-side
drain port. Save for use in step 3.
2. Secure Hose A to front cover drain port with a hose
clamp. Route hose to rear right side panel grommet
hole.
HOSE A
FRONT COVER
DRAIN PORT
TUBE(S) 2
Upright "Alternate" Connections
Right Side Only
(Upflow Shown, Counterflow Similar)
3. Remove grommet from front right-side panel drain hole.
Seal hole in grommet with large end of plug. Reinstall
grommet and plug into side panel drain hole.
4. Cut 1/4 inch from the end of the drain port on the exter-
nally mounted rubber elbow. Discard cut portion.
5. Insert Tube 1 into rubber elbow drain port and secure
with hose clamp. Angle tube outward toward front of
furnace.
"X" Length to Cut From
Long End of Hose B
(inches)
8 inches
4 inches
None
RUBBER ELBOW
(EXTERNALLY
MOUNTED)
RUBBER
ELBOW
DRAIN PORT
TUBE 1
HOSE
CLAMPS
(5 PLACES)
HOSE B
SIDE PANEL
GROMMET
HOLES
DRAIN TRAP