Alcatel OmniAccess 512 Getting Started Manual
Alcatel OmniAccess 512 Getting Started Manual

Alcatel OmniAccess 512 Getting Started Manual

Omniaccess 512

Advertisement

OmniAccess
512
TM
Getting Started Guide
May, 2002

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OmniAccess 512 and is the answer not in the manual?

Questions and answers

Summary of Contents for Alcatel OmniAccess 512

  • Page 1 OmniAccess Getting Started Guide May, 2002...
  • Page 2 The switches should always be properly grounded. Lithium Batteries Caution: Return the module with the Lithium battery to Alcatel. The Lithium battery will be replaced at Alcatel’s factory. All-In-One Service Programs: The features and specifications described in this manual are subject to change without notice.
  • Page 3: Table Of Contents

    Table of Contents Introduction OmniAccess Basics ......1 ....12 Unpack the Switch .
  • Page 4: Introduction

    IP address User-installable USP, T1/E1, and ISDN submodules provide flexibility. VoIP (Voice Over IP) uplink This guide also includes sections on OmniAccess 512 submodules and compression/encryption SIMMs are basics. Refer to these sections for general OmniAccess also supported on the OA-512. Virtual Private Network chassis and LED information.
  • Page 5: Unpack The Switch

    Attach the second bracket to the opposite side of the switch using the remaining screws. If you discover or suspect any damage, contact your OmniAccess 512 distributor immediately. Carefully lift the switch and insert it into the rack.
  • Page 6: Install An Uplink Submodule

    OA-512 switches. o Note o OmniAccess switches do not support the Alcatel Backup Power System (BPS). Connect the provided power cord to the power connector on the OmniAccess. Then plug the power cord into a properly grounded electrical outlet.
  • Page 7: Verify The Management Leds

    Solid Green Until you configure your OmniAccess 512 switch via the built-in software, When the OmniAccess 512 is powered up, extensive the attached devices will not be acces- power-on diagnostics are performed. As a result, you sible from the network. Refer to the...
  • Page 8: Connect The Console Port

    This section covers procedures for setting up your Connect the other end of the serial cable to a PC or OmniAccess 512 software. Procedures include workstation equipped with terminal emulation soft- ware. You will use this connection to enter initial •...
  • Page 9 See the “Switch Security” chapter in your OmniAccess User Manual for details. The OmniAccess 512 is factory-configured to boot up (Command Line Interface) mode. The allows The following procedure uses the...
  • Page 10: Set Up A Password

    Main Menu. Only the system prompt ( ) will appear. -> For more information on using the refer to the OmniAccess 512 User o Important Note o Manual To create an all-numeric password (for example, ), you must enter...
  • Page 11: Set The System Time And System Date

    o Caution o c. To view the system date, enter at the prompt and press . The system date Your password is stored (encrypted) will be displayed, as shown here: in the configuration file. If you remove this file and reboot the ->...
  • Page 12 b. To specify the department or network adminis- d. To specify a system name, type trator for the switch, type followed by a text-string name at the prompt followed by a text-string name you want to use and press . For example, to specify at the prompt and press .
  • Page 13 o Important Notes o To specify the system location, type followed by text-string name at the Any text-string name that includes prompt and press . For example, to spec- spaces must be enclosed in quotes as the system location, (e.g., type the following at the prompt and press No confirmation message will appear...
  • Page 14: Assign An Ip Address To The Default Group

    See your type at the prompt and press OmniAccess 512 User Manual and any supplements for information on all switch commands. 7. Assign an IP Address to the Default Group 8. Log Out Your switch is configured with a default Group and .
  • Page 15: Omniaccess Basics

    OmniAccess Basics This section provides general information on the OA-512 chassis and s. For more detailed informa- tion, refer to the OmniAccess 512 User Manual. Management LEDs Ethernet Port Connectors Slot for VoIP Uplink Submodule Each OA-512 chassis provides OA-512 switches provide twelve 10/100 OA-512 switches provide a slot for a Voice over four Management LEDs.
  • Page 16: Oa-512 Slot Numbering

    OA-512 Slot Numbering The front panel of an OA-512 is divided into several areas labeled S2, S3/1, S3/2, S/4, etc. Think of these areas as a division of the switch into several modules, or slots. The UI and CLI, accessible via the front panel console port, rely on these slot designations for many of their management and configuration commands.
  • Page 17: Oa-512 Rear Panel

    . P l e a s e r e f e r t o t h e daughtercard (MEM512-FLSH-16M). HWE). A compression/encryption SIMM OmniAccess 512 User Manual for is required to run Virtual Private network information on the DC version (OA- (VPN) software.
  • Page 18: Oa-512 Management And Port Leds

    OA-512 Management and Port LEDs (Hardware Status). This LED displays (Temperature). If the internal switch Green when the switch has successfully temperature is approaching maximum passed power-on hardware diagnostics. It operating limits, this LED will display displays Amber if the hardware has failed Green.
  • Page 19: The User Manual On Cd

    Product specifications contained in this document are subject to change without notice. C ontact your local Alcatel representative for the most current information. C opyright © 2 0 0 3 Alcatel Internetworking, Inc. All rights reserved. This document may not be reproduced in whole or in part without the expressed written permission of Alcatel Internetworking, Inc.

This manual is also suitable for:

Oa-512

Table of Contents