Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Amano 4700 Series
Summary of Contents for Amano 4700 Series
-
Page 1: User Manual
888 534-5994 4700 - 4800 Series USER MANUAL... -
Page 2: Table Of Contents
Table of Contents Table of Contents..............i Introduction .................1 Preparation Before Use ............1 How To Take Off The Case..........1 How To Operate ..............2 How To Set The Typewheels..........2 How To Set The Clock ............3 How To Change A Ribbon ..........5 Adjustment of Printing Position ........6 Printing Sample .............. - Page 3 4700/4800 Series Time Stamp Operation Manual...
-
Page 4: Introduction
Introduction This manual explains how to use your 4700/4800 Series Time Stamp. You are strongly encouraged to read this manual completely before using the 4700/4800 Time Stamp, and to retain it for future reference. Preparation Before Use (Refer to Fig. 1, 2, & 7) To prevent possible damage of the machine during transit, shock absorbing material has been put inside the machine body (hammer section). -
Page 5: How To Operate
Shaft Shaft Holder Clock Face Figure 2. To Set the 4700 Series (Year, Month, Date, Time) • Keeping the electrical cord to A.C. main, push the minute advance lever [5] as shown in Figure 5, in the arrow direction, then turn the typewheels [3] for year, month, date, hour and minute in the direction of the arrow shown in Figure 3 and set one minute before the desired time. -
Page 6: How To Set The Clock
• On releasing the minute advance lever [5], the minute typewheel advances one minute to synchronize with the desired time. Clock Face Typewheels Figure 3. To Set the 4800 Series Model 4850 …4 digit numbers (Year, Month, Date, Hours & Minute) Model 4850 …5 digit numbers )Month, Date, Hours &... - Page 7 • To advance the typewheel and clock at the same time, push the minute advance lever [5] (see Figure 5) in the arrow direction, so the typewheel and clock hand advance one minute at the same time. Caution: The setting of the typewheel should be done only right after the minute typewheel is advanced! Shaft Clock Face...
-
Page 8: How To Change A Ribbon
How To Change A Ribbon (Refer to Fig. 6 & 7) • In case the print color becomes too light, or the ribbon is cut or crumpled too much, please replace the ribbon with a new one. • First check whether the ribbon reverse turn lever [6] (see Figure 6) is inclined to the inner side of the machine. -
Page 9: Adjustment Of Printing Position
Ribbon Spool Ribbon Fixer Ribbon Guide Shaft Ribbon Spool Figure 7. Adjustment of Printing Position (Refer to Fig. 8, 9 & 10) • The printing position can be adjusted by moving the knob [11] (see Figures 8 & 9) between 37 mm – 83 mm (1.5” – 3.25”) from the top of the paper. - Page 10 Knob for printing adjustment Figure 8. Figure 9. 4700/4800 Series Time Stamp Operation Manual...
-
Page 11: Printing Sample
Printing Sample Figure 10. Incase the printing is required on paper narrower than 65 mm (2 5/8”), install the polyester sheet supplied as accessory in between the bottom case and slide plate as per illustration by placing the sheet so as the edge cut side comes to the right-hand side. -
Page 12: Caution On Use
Caution On Use • DO NOT touch the clock hands in any case. • When the printing color becomes light, replace the ribbon with a new one. DO NOT paint with stamping ink as this could injure the machine. • When cleaning the typewheel, carefully remove the dust lodged between the typewheels.
Need help?
Do you have a question about the 4700 Series and is the answer not in the manual?
Questions and answers