Operating and installation instructions Gas hobs KM 3034 KM 3054 en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
Per questo se si vuole usare l’apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.
Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß...
Description of the appliance KM 3034 a Large burner Cooking zone controls: b Small burner k Front right c Wok burner l Rear right de Medium burners m Middle f Pan support (for each burner) n Rear left o Front left...
Description of the appliance KM 3054 a Wok burner Cooking zone controls: b Large burner g Front right c Small burner h Rear right de Medium burners i Rear left f Pan support (for each burner) j Front left k Left l Cooking zone symbol m Residual heat indicator n Minute minder...
Description of the appliance Accessories supplied The accessories supplied with your appliance as well as a range of optional ones are available to order from Miele (see "Optional accessories"). Wok ring The Wok ring supplied with your appliance can be used in instances where extra stability is required.
Description of the appliance Minute minder display a Lock/Timer b Sensor switch: - Select minute minder - Switch between timer functions - Select cooking zone c Indicator lamp for minute minder d Indicator lamp for relevant zone, e.g. back right-hand cooking zone e Timer display 00 to 99 = Time in minutes 0.^ to 6.^ = Time in hours...
Description of the appliance Burner Wok burner a Outer burner cap b Inner burner cap c Burner head d Burner base e Ignition safety device f Ignitor Small, medium and large burners a Burner cap b Burner head c Burner base d Ignition safety device e Ignitor...
Any other use is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation. The gas hob is not intended for outdoor use.
Warning and Safety instructions Safety with children Activate the safety lock to ensure that children cannot switch on the appliance inadvertently. This appliance is not a toy! To prevent the risk of injury, do not allow children to play with the appliance or its controls. Children under 8 years of age must be kept away from the hob unless they are constantly supervised.
It is most important that this basic safety requirement is observed and tested regularly, and where there is any doubt, the household wiring system should be inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
The hob is not intended for use with an external timer switch or a remote control system. If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from the Miele Spare Parts Department.
Warning and Safety instructions Do not connect the appliance to the mains electricity supply by a multi-socket adapter or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating). Do not use the hob if if it is faulty, or if the ceramic surface is cracked, chipped or damaged in any way.
If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or surrounding units and also parts of the hob. Miele cannot be held liable for this type of damage.
Warning and Safety instructions Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan. Unless the pan manufacturer states that you can do so, do not use pans with very thin bases on this hob, and never heat up empty pans as they could get damaged.
If the appliance has not been used for a longer period of time it should be thoroughly cleaned before it is used again. It is also advisable to have the appliance tested for safety. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment.
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate" section of this booklet. Cleaning for the first time ^ Remove any protective foil. ^ Clean all removable parts of the burners with a solution of warm water and a little washing-up liquid applied with a soft sponge.
Operation Rapid ignition system The appliance has a rapid ignition system with the following features: – Rapid ignition without pressing and holding the control dial – Automatic re-ignition If the flame is extinguished by a draught, etc. the burner is automatically reignited.
Operation Switching on When using the gas hob an extractor hood or a ventilation device must be used. ^ The control for the burner required must be pressed in and turned anti-clockwise to the largest flame symbol to switch on. The ignitor will make a clicking sound and ignite the gas.
Operation Regulating the flame Regulate the flame so that it does not spread out beyond the sides of the pan. As the outer part of the flame is much hotter than the centre, the tips of the flames should stay beneath the pan base.
Operation Easy switch-off function All active cooking zones can be switched off by touching the easy switch-off sensor f. ^ Touch the f sensor. The in-operation/residual heat indicators for active cooking zones will flash. A minute-minder time set will continue to run down, if it is not allocated to a specific cooking zone.
Minute minder You can select a time from 1 minute (01) to 6 hours (6^). If a time of more than 99 minutes (99) is set, the time is set in half-hour steps. The half hour is indicated by a dot after the number.
Minute minder Allocating the minute minder to a specific cooking zone You can set the minute minder for any active cooking zone. All cooking zones can be programmed at the same time. ^ Switch on the desired cooking zone. ^ Touch the m sensor. 00 and the minute minder indicator lamp will flash in the timer display.
Suitable pans Burner Min. pan base diameter in cm Small burner Medium burner Large burner Wok burner Max. diameter at top of pan in cm Small burner Medium burner Large burner Wok burner – Refer to the chart above and ensure that the pan diameter falls within the minimum and maximum diameters given for the burner you are using.
Suitable pans Combi insert The combi insert must be utilised when using pans with a base diameter of less than the minimum given in the table above. The combi insert ensures that the pan will sit securely on the hob, and cannot tip up. Wok ring The Wok ring supplied with your appliance can be used in instances where extra stability is required.
Energy saving tips – Use a pan lid whenever possible to minimise heat loss. – Cook with as little water as possible. – Cooking times are greatly reduced when using a pressure cooker. – Turn the flame down promptly to a lower setting when the pan has come to the boil.
Safety features Thermo-electric ignition This appliance is has a thermo-electric ignition safety device. If the flame goes out, for example if food has boiled over or if there is a sudden draught, and automatic re-ignition has been unsuccessful, the supply of gas to the burner will be cut off preventing any further escape of gas.
Cleaning and care Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit. – The appliance should be cleaned after each use. Allow the appliance to cool down to a safe temperature before cleaning.
It will form an invisible coating which will cause permanent Clean with Miele ceramic glass and stainless steel discolouration of the cleaner (see "Optional Accessories"), or with ceramic surface which another proprietary ceramic glass cleaner and cannot be removed.
Cleaning and care To assemble the small, medium and large burners ^ Place the burner head b on to the burner base c so that the ignition safety device d and the ignitor e extend through their respective holes in the burner head. The burner head must click into place correctly.
Cleaning and care To assemble the wok burner ^ Place burner head c onto burner base d so that the ignition safety device e and the ignitor f extend through their respective holes in the burner head. The burner head must click into place correctly.
Problem solving guide With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. saving you both time and money. The following guide may help you to find the reason for a fault, and to correct it.
Problem solving guide Problem Possible cause Remedy The burner does not There could be an air lock in the You may need to make several ignite when the hob is gas pipe. attempts before the burner ignites being used for the first successfully.
Problem solving guide Problem Possible cause Remedy The ignitor on the Check whether the mains If it has, contact a qualified electrician or the Miele Ser- burner does not fuse has tripped. vice Department. spark. - Food residues between Remove any soiling. Please see "Cleaning and care" for the ignitor and details.
Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your appliance. These products can be ordered online: or from Miele (see back cover for contact details) Ceramic and stainless steel hob cleaner...
Safety instructions for installation Do not use any sealant except Fit the wall units and extractor hood where expressly instructed to do so. before fitting the hob to avoid The seal underneath the appliance damaging the surface. provides a sufficient seal for the worktop.
Safety instructions for installation Safety distance above the appliance A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood, a minimum safety distance of at least 760 mm must be maintained.
Safety instructions for installation Safety distances to the sides of and behind the appliance Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illustrations).
Installation ^ Make the worktop cut-out according to the dimensions given in the building-in dimension diagram. Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Seal the cut surfaces on wood/laminated worktops with a suitable heat-resistant sealant to avoid swelling caused by moisture.
Installation Seal between appliance and Tiled worktop worktop Grout lines a and the hatched area The sealing strip under the edge of the underneath the hob frame must be top part of the appliance provides a smooth and even. If they are not the sufficient seal for the worktop.
Electrical connection Connection should be made via a All electrical work should be carried suitable isolator or a double pole fused out by a suitably qualified and spur connection unit which complies competent person, in strict with national and local safety accordance with current local and regulations and the on/off switch should national safety regulations (BS 7671...
If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from the Miele Service Department. The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection.
Please contact your dealer or the Miele Spare Parts Department for the Check with your local gas supplier appropriate conversion jets if about the type of gas and its necessary.
Gas connection Connection Using a 90° angle The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit, and the isolating valve must be easily accessible and visible (by opening one of the kitchen doors, if necessary).
Burner ratings Nominal rating KM 3034 / KM 3054 Burner Gas type High setting Low setting Small burner Natural gas H 0.25 Liquid gas 0.95 0.20 Medium burner Natural gas H 0.30 Liquid gas 0.35 Large burner Natural gas H 0.50...
Conversion to another type of gas Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g.
Conversion to another type of gas Changing the jets Disconnect the gas hob from the mains electricity supply. Turn off the gas supply. To change the main jets Small, medium and large burners ^ Remove the pan support, burner cap a and burner head ^ Using an M7 socket spanner, unscrew the main jet f ^ Fit the correct jets securely (see jet table).
Conversion to another type of gas Wok burner ^ Remove burner cap ab and burner head c. ^ Using an M7 socket spanner, unscrew the main jet d ^ Fit the correct jets securely (see jet table). ^ Finally, secure the jets against inadvertent loosening with sealing wax.
Conversion to another type of gas To change the small jets To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Pull the control knobs off. ^ Remove the cover (see illustration). ^ Lift the top of the appliance off.
Conversion to another type of gas Function test Check all gas fittings for leaks. ^ Reassemble the appliance. ^ Check the burner flame by operating the burner. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting. On the highest setting, the flame must have a distinctive and visible core.
Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance. These are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.