Miele KM 3054-1 Manual
Hide thumbs
Also See for KM 3054-1:
- Operating and installation instructions (60 pages) ,
- Installation manual (18 pages) ,
- Installation manual (21 pages)
Table of Contents
Advertisement
Quick Links
Installation
Safety instructions for installation
Risk of damage from incorrect connection.
Incorrect installation can cause damage to the hob.
The hob must only be installed by a qualified person.
Damage from falling objects.
Take care not to damage the hob when fitting wall units or a cooker hood above
it.
Fit the wall units and the cooker hood before the hob.
The room in which the hob is installed must conform to all relevant
local and national building regulations and safety regulations.
The veneer or laminate coatings of worktops (or adjacent kitchen
units) must be treated with 100 °C heat-resistant adhesive which will
not dissolve or distort. Any backmoulds must be of heat-resistant
material.
The hob must not be installed over a fridge, fridge-freezer, freezer,
dishwasher, washing machine, washer-dryer or tumble dryer.
A gas hob must not be installed directly next to a deep fat fryer as
the gas flames could ignite the fat in the fryer. It is essential to
maintain a distance of at least 300 mm between these two
appliances.
When installing the hob, make sure that the gas pipe and
electrical connection cable cannot come into contact with hot
appliance parts.
The electrical cable and any flexible gas connection pipes must be
installed in such a way so that they do not come into contact with
any moving kitchen parts (e.g. a drawer), and cannot become
trapped.
Observe carefully the safety clearances listed on the following
pages.
11615020-02
Advertisement
Table of Contents
Related Manuals for Miele KM 3054-1
Summary of Contents for Miele KM 3054-1
- Page 1 *INSTALLATION* 11615020-02 Installation Safety instructions for installation Risk of damage from incorrect connection. Incorrect installation can cause damage to the hob. The hob must only be installed by a qualified person. Damage from falling objects. Take care not to damage the hob when fitting wall units or a cooker hood above Fit the wall units and the cooker hood before the hob.
-
Page 2: Installation
*INSTALLATION* 11615020-02 Installation Safety distances Safety distance above the hob A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood or if any flammable objects (e.g. - Page 3 *INSTALLATION* 11615020-02 Installation Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illustrations).
- Page 4 *INSTALLATION* 11615020-02 Installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance ...
-
Page 5: Installation Notes
*INSTALLATION* 11615020-02 Installation Tiled worktops Installation notes Seal between the hob and the worktop Grout lines and the hatched area underneath the hob frame must be smooth and even. If they are not the hob will not sit flush with the worktop and the sealing strip underneath the ... -
Page 6: Building-In Dimensions
*INSTALLATION* 11615020-02 Installation Building-in dimensions All dimensions are given in mm. a Front b Casing depth c Mains connection box with mains connection cable, L = 1440 mm d Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226) e Electronics housing, maximum casing depth 78 mm... - Page 7 *INSTALLATION* 11615020-02 Installation Installing the hob Installation Stick the supplied sealing strip under Preparing the worktop the edge of the hob. Create the worktop cut-out as shown Feed the power cable for the hob in the hob diagram. Remember to down through the worktop cut-out.
- Page 8 *INSTALLATION* 11615020-02 Installation Securing the hob Functional check After installing the hob, ignite all burners to check that they are operating correctly: - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.
- Page 9 *INSTALLATION* 11615020-02 Installation Gas connection Connection to the gas supply must be carried out in strict accordance According to the Gas Safety with current local regulations. Every (Registration of Gas Installers and appliance should have its own easily Gas Contractors) Regulations, any accessible isolating valve and test gas installation work including the point.
- Page 10 Please appropriate class and is employed contact your supplier or Miele for the by a registered gas contractor. appropriate conversion jets if necessary. Conversion to another type of gas is described under „Conversion...
- Page 11 *INSTALLATION* 11615020-02 Installation Gas Governor LP Gas Connection - elbow joint connection The gas governor is only included with appliances set up for connection to Town gas. a Elbow join b Gasket a Connection to the hob c Nozzle b Outlet pressure (10 mbar) d Ring c Gas Governor e Rubber hose...
-
Page 12: Burner Ratings
*INSTALLATION* 11615020-02 Installation Burner ratings Nominal ratings Burner Gas type Highest setting Lowest setting Small burner Natural gas – 0.25 Town gas – 0.19 Liquid gas 0.95 Medium Natural gas – burner Town gas – 0.38 Liquid gas 0.35 Large burner Natural gas –... - Page 13 (RCD) with a trip Danger of injury. range of 30 mA. Miele cannot be held liable for unauthorised installation, maintenance and repair work as this can be dangerous to users. Miele cannot be held liable for...
- Page 14 H 05 VV-F with a suitable cross section. A suitable following depending on installation: connection cable is available to order Safety fuses from Miele. Completely remove fuses. Automatic circuit breakers Press the (red) test button until the middle (black) button springs out.
-
Page 15: Converting To Another Gas Type
*INSTALLATION* 11615020-02 Converting to another gas type Jet table Risk of explosion due to an incorrect conversion. The jet markings refer to a ¹/₁₀₀ mm If the conversion to another type of bore diameter. gas is carried out incorrectly, it may ... - Page 16 *INSTALLATION* 11615020-02 Converting to another gas type Wok burner Changing the jets Disconnect the hob from the electricity supply and turn off the gas supply. Changing the main jets Small, medium and large burners Remove burner caps and burner head .
- Page 17 *INSTALLATION* 11615020-02 Converting to another gas type Secure the jets against inadvertent Changing the small jets loosening with sealing wax. To change the small jets, the burner fixing screws must first be loosened and the upper section of the appliance removed.
- Page 18 *INSTALLATION* 11615020-02 Converting to another gas type Functional check Check all gas fittings for leaks. Reassemble the hob. Ignite all burners to check that they are operating correctly. - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.