Sangean ATS-303 User Manual
  1. Manuals
  2. Brands
  3. Sangean Manuals
  4. Radio
  5. ATS-303
  6. User manual

Sangean ATS-303 User Manual

Ats-303
Hide thumbs

Advertisement

Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ATS-303 and is the answer not in the manual?

Questions and answers

Related Manuals for Sangean ATS-303

Summary of Contents for Sangean ATS-303

  • Page 2 TUNING POWER DISPLAY STAND BY TIME SET STEREO MONO TUNING MEMO PRESET TUNING ATS-303 6V DC 6V DC...
  • Page 3 Elements of operation LCD DISPLAY Frequency, time and function displays MEMO1-5 Entering commands STAND BY Alarm standby DISPLAY Time display and time input TIME SET STEREO/MONO Switching from Stereo/Mono 10-90 Sleep PRESET TUNING 1-5 Station keys TUNING< > Setting stations manually Automatic station search Entering clock time and alarm time On/off key,Switching off the alarm and the...
  • Page 4 SW FREQ Switching over the automatic tuner METER Searching through the SW metric channels FULL Searching through all frequencies 9K/10K Tuning steps 9kHz/10kHz Displays Selecting a frequency range Frequency and time displays kHz for MW/MHz for FM and SW Radio alarm HWS beeper alarm Sleep Mode of operation locked...

  • Page 5: Power Supply

    Power supply This appliance can be operated with: 4 Mignon batteries 1.5 Volt,Type IEC R6/UM3/AA or Changing the batteries Open the battery compartment by pressing on the finger groove on the lid of the battery compartmint and pulling it down.lnsert4, 1.5 Volt Mignon-batteries taking care that the polarity of the batteries corresponds with that shown next to the battery compartment.

  • Page 6: Setting The Clock

    RADIO Setting the clock In accordance with the world standard,the time is displayed on a 24 hour basis(Greenwich mean time). The clock is ready for operation after four 1.5 volt Mignon batteries have been inserted into the battery compartment. Press the DISPLAY/TIME SET key a little longer than half a se- cond.0:00 blinks in the display.
  • Page 7 Enter the time using the TUNING keys while the display is bin- king. The < key adjusts the hours and the > key adjusts the minutes. To start the time display press DISPLAY/TIME SET once again. If DISPLAY/TIME SET is not pressed after entering the time,the time you have set becomes valid automatically after approx.5 se- conds.
  • Page 8 RADIO Channel Frequency range Wavelength 87.5-108MHz 522-1620kHz Medium wave with 9 kHz tuning steps 520-1710kHz Medium wave with 10 kHz tuning steps 2.3-7.3MHz Short wave 120-41m 9.5-26.1MHz Short wave 31-11m After switching on the appliance using the POWER key ,the fre- quency range and frequency which were last used are shown in the display.After switching the wave range switch,the channel and fre- quency selected appear in the display.
  • Page 9 To make this choice,the SW FREQ:METER/FULL switch has to be moved using a small screwdriver or similar instrument. Important note: The SW FREO: METER/FULL switch also has a RESET function. After switching over switch and then switching the appliance off and on, all of the stored values are erased. Therefore, switch should be set before setting the time and the alarm or programming the station keys.

  • Page 10: Manual Tuning

    RADIO Manual tuning Switch the appliance on,select a wave range and find your desired station by pressing the TUNING keys repeatedly.The perfect set- ting and the strength of the reception of the station is shown by the signal lamp TUNING. By pressing and holding one of the keys ,you can manually...

  • Page 11: Automatic Station Search

    Automatic station search If one of the TUNING keys is pressed for longer than half a se- cond,the station search is triggered.The key pressed is to be relea- sed after the station search has begun. As soon as a station is found which good quality reception the station search stops antomatically.
  • Page 12 RADIO As soon as the station has been selected, press the MEMO key 1-5.M blinks for approx.3 se- conds in the display During this time,press the station key 7 PRESET TUNING 1-5 at which you wish to store the stati- Then press the MEMO key once again.
  • Page 13 The socket for the headphones , which is suitable for a cinch plug of 3.5mm diameter, is mar- ked with the headphone symbol. The in-built loudspeaker switches off automatically and the applian- ce is now ready to receive stereo stations. Slide the STEREO/MONO switch to STEREO.

  • Page 14: Setting The Alarm Function

    RADIO The operational lock is on when switch is under the key sym- bol. The On/OFF switch and all tuning options are not functional. lt is not possible to switch the appliance on until the operational lock has been deactivated.When the machine is switched off, the operational lock ensures that the machine is not turned on accidentally, for ex- ample when being transported in a suitcase or bag.

  • Page 15: Radio Alarm

    Now you can set the desired alarm time with the TUNING keys ,with the same procedure as when setting the time. The < key sets the hours and the > key sets the minutes. After entering the alarm time, the normal time display returns afte approx.

  • Page 16: Switching Off The Alarm

    RADIO HWS beeper alarm To be woken by the HWS beeper. slide the STAND BY switch the alarm symbol which then also appears in the display. The HWS beeper begins quietly and becomes progressively louder to wake you up. During the alarm process the symbol blinks in the display.

  • Page 17: Specifications

    Sleep When the key 10-90 is pressed, the appliance is switched on auto- matically and the playing time of 90 minutes is selected. So you can fall asleep while listening to the radio, knowing it will switch itself off. The appliance switches itself off after the selected time is over. The duration of play can be selected in 10 minute steps between 10 and 90 minutes by holding key 10-90.The symbol...

Table of Contents