Related Manuals for Valcom V-5328020
Summary of Contents for Valcom V-5328020
- Page 1 ® PagePac ISSUE 2 PagePac Plus AmpliCenter V-5328020/V-5328100/V-5328300 Installation and Use 947169...
-
Page 2: Installation Steps
Installation Steps ® Mount the PagePac Plus AmpliCenter to either the wall Note: If installed next to other equipment, including the (Figure 1), cabinet, or a 19 inch rack (Figure 2). PagePac Plus Controller and Zone Expansion Units, leave at least four inches space above and below for proper SIDE VIEW ventilation. - Page 3 Connect music input wires to Left, Right, and Ground terminals, if stereo, or Left and Ground, if not (see Figure 3). Note: The optional audio background music source can be a CD or tape player, AM, FM, or commercial radio, or other audio device.
- Page 4 Note: Connect the 4-wire RJ-11 type plug (used with telephones) to the Page Input connector (far right), or use the Page in terminals. Use Tip and Ring if installing to an existing paging system (low voltage output), VOX activated. Use Tip and Ring if connecting to a Loop Start or Ground Start interface port in host telephone system.
- Page 5 Adjust sound levels using AmpliCenter controls, if necessary. Note: If no page is heard, refer to the troubleshooting Using a small standard screwdriver, make the following adjustments (see Figure 8). Guidelines. Figure 8. Test Page Adjustments Adjust the Low Frequency Cut Off control. This control cuts out the low frequency bass so that horns and small speakers are not over-driven and distorted by excessive bass energy.
-
Page 6: Troubleshooting
Troubleshooting Some common problems encountered when the paging system is not operating are described below. Check each item in the order listed. No AC power to AmpliCenter. Host telephone system failure. Host system page port failure. ® A hardwire disconnect between host system and PagePac Plus. -
Page 7: Controls And Indicators, Terminals And Connectors
Controls and Indicators, Terminals and Connectors Figure 9 shows the controls and indicators, terminals and connectors on the rear panel of the AmpliCenter. Table 2 identifies them by function. PAGE PAGING IN MUSIC IN 70V OUT INPUT CONTROLLER 0 dBm UNIT LOW FREQ CUT-OFF... -
Page 8: Connecting Speakers
Connecting Speakers Locate and mount all speakers in accordance with the floor plan drawing for this installation. Connect each speaker to the appropriate home run or speaker-to-speaker wiring scheme as shown on the wiring plan (see Figure 10). Test speaker wiring for short circuits. Measure the resistance of each home run wire run with an ohmmeter. -
Page 9: Example System Setups
Example System Setups Figure 11 illustrates the interconnection between the AmpliCenter and the Controller, if used. Figure 12 illustrates the interconnection of two or more AmpliCenters. Note: If the AmpliCenter is used ® with the PagePac Plus Controller, refer to the Controller Installation and Use 105 - 120 VAC 210 - 2 0 VAC... -
Page 10: Technical Assistance
When calling, have a VOM and a telephone test set available and call from the job site. Call (540) 427-3900 and ask for PagePac Technical Support, or call (540) 427-6000 for Valcom 24- hour Automated Support or visit our websites at http://www.pagepac.com and www.val- com.com. -
Page 11: Specifications
Specifications Table 4 describes the specifications of the AmpliCenter D20, D100, and D300 models. Table 3. AmpliCenter Specifications Features Telephone Paging Access: The AmpliCenter accepts inputs from telephone system (PBX) ground start or loop start trunk ports, dry loop 600 ohm page ports, dry loop (hi Z), or amplified microphones. Music interface: The AmpliCenter is the unit to which the background music source (CD, radio, tape player) is connected, for distribution to the paging system.