Door Closing And Door Alignment; Filters And Accessories; Install Air Filter - Whirlpool REFRIGERATOR User Instructions

Door Closing and Door Alignment

IMPORTANT: To comply with American Disabilities Act (ADA)
guidelines, fully retract the rollers into the cabinet to lower the
refrigerator.
Door Closing
The base grille covers the leveling screws and roller assemblies
located at the bottom of the refrigerator cabinet below the freezer
drawer. Before making adjustments, remove the base grille and
move the refrigerator to its final location.
1. Remove the base grille. Grasp the grille firmly and pull it
toward you.
2. Move the refrigerator to its final location.
NOTE: To allow the refrigerator to roll easier, raise the leveling
legs off the floor by turning the leveling screws
counterclockwise. The front rollers will be touching the floor.
3. So the doors will close easier, use a
leveling screws clockwise. This will raise the front of the
refrigerator tilting it slightly downward to the rear. Turn both
leveling screws the same amount.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws. This
makes it easier to turn the screws.
A. Leveling screw
B. Front roller
4. Open both doors again to make sure they close as easily as
you like and that they stay closed. If not, tilt the refrigerator
slightly more to the rear by turning both leveling screws to the
right. It may take several more turns.
NOTE: To keep the refrigerator level, you should turn both
leveling screws the same amount.
5. Replace the base grille.
Pull open the freezer drawer.
Align the three clips on the back of the base grille with the
three tabs at the base of the refrigerator.
Push the base grille in toward the refrigerator until it is
firmly in place.
B. Clip
10
" hex driver to turn both
"
A
B
A
B
A. Tab
Door Alignment
If the space between the refrigerator doors and freezer drawer
looks uneven, you can adjust it using the following instructions:
1. Remove the top hinge cover.
2. Loosen the top hinge screws using a
3. Have someone hold the door in place or put a spacer between
the doors and drawer.
4. Tighten the top hinge screws once the door is in the desired
location.
5. Replace the top hinge cover.
FILTERS AND
ACCESSORIES

Install Air Filter

(on some models)
The air filter reduces the buildup of odors. This helps to maintain a
cleaner environment inside the refrigerator.
On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use. On some models,
the air filter is already installed at the factory.
Installing the Air Filter
Install the air filter behind the vented door, located along the rear
interior wall of the refrigerator compartment.
1. Remove the air filter from its packaging.
NOTE: An air filter status indicator is included with the air filter.
The indicator is not needed for models that display the air filter
status on the control panel.
2. Lift open the vented door.
3. Snap the filter into place.
Air Filter Status Indicator
The control panel displays the Air Filter status.
GOOD - The air filter icon on the control lights up in BLUE.
ORDER a replacement - The air filter icon on the control lights
up in YELLOW.
REPLACE air filter - The air filter icon on the control lights up in
RED and "Replace Filter" will appear.
EXPIRED - The air filter icon lights up in RED and "Replace
Filter" flashes on the control display.
After replacing the air filter, press and hold the AIR FILTER button
for 3 seconds. The filter icons will turn off. See "Using the
Control(s)." When the system is reset, the air filter icon will return
to its BLUE color and the words "Replace Filter" will disappear
from the display.
NOTE: At any filter status, pressing and holding the AIR FILTER
button for 3 seconds will reset the air filter status to Good and the
air filter icon will turn off.
" socket or wrench.