Advertisement
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Identifier
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
WM-203
Retain This
Manual for
Reference
08-09-07
OWNER'S
MANUAL
COMPETITOR
WM-203 COMBO BENCH
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
®
IMPEX
INC.
Advertisement
Table of Contents
Related Manuals for Impex Competitor WM-203
Summary of Contents for Impex Competitor WM-203
- Page 1 NOTE: Please read all instructions carefully before using this product Table of Contents COMPETITOR Safety Notice WM-203 COMBO BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model WM-203 Retain This Manual for Reference 08-09-07 OWNER'S MANUAL ®...
-
Page 2: Table Of Contents
ASSEMBLY INSTRUCTIONS..................EXPLODED DIAGRAM....................PARTS LIST......................…. WARRANTY......................…. ORDERING PARTS....................…. BEFORE YOU BEGIN Thank you for selecting the Competitor WM-203 COMBO BENCH by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notice
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. - Page 4 WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
-
Page 5: Hardware Pack
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size. -
Page 6: Assembly Instruction
ASSEMBLY INSTRUCTION Tools required assembling the machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this equipment to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Secure them with two M10 x 2 ¾”... - Page 7 STEP 2 (See Diagram 2) A.) Connect the Front Stabilizer (#5) to the Main Seat Support (#3) and secure them with three M8 x ¾” Hex Bolts (#41) and Ø 5/8” Washers (#45). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support to the Cross Brace (#2).
- Page 8 STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#9) to the bracket on the Front Stabilizer (#5). Secure it with one M10 x 2 ¾” Hex Bolt (#38), Ø ¾” Washer (#44), and M10 Aircraft Nut (#47). Do not over tighten the Nut and Bolt.
- Page 9 STEP 4 (See Diagram 4) A.) Attach the Backrest Supports (#14) onto both ends of the Pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#8). B.) Place the Backrest Board (#17) onto the Backrest Supports. Secure it with four M6 x 1 ½”...
- Page 10 STEP 5 (See Diagram 5) A.) Attach the ball end of the Cable to the Pulley (#30). Place the Pulley in the open slot on the Upper Lat Bar Frame. Secure it with one M10 x 2” Hex Bolt (#40), two Pulley Bushings (#29), and one M10 Aircraft Nut (#47).
-
Page 12: Parts List
PARTS LIST KEY NO. DESCRIPTION QUANTITY Rear Upright Beam Cross Brace Main Seat Support Diagonal Support Front Stabilizer Right Bar Catch Left Bar Catch Backrest Adjustment Bar Leg Developer Foam Tube Weight Holder Lower Lat Bar Frame Lat Bar Backrest Support Arm Curl Stand Bracket Backrest Board... -
Page 13: Limited Warranty
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase.