1. Manuals
  2. Brands
  3. Impex Manuals
  4. Home Gym
  5. MARCY MWM-1860
  6. Owner's manual

Impex MARCY MWM-1860 Owner's Manual

Marcy home gym
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-1860
Retain This
Manual for
Reference
110726
OWNER'S
MANUAL
®
MARCY
HOME GYM
IMPEX
2801 S. Towne Ave, Pomona, CA 91766
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
MWM-1860
®
INC.

Advertisement

Table of Contents
loading

Related Manuals for Impex MARCY MWM-1860

Summary of Contents for Impex MARCY MWM-1860

  • Page 1 NOTE: Please read all instructions carefully before using this product Table of Contents ® Safety Notice MARCY MWM-1860 Hardware Pack HOME GYM Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM-1860 Retain This Manual for Reference 110726 ®...

  • Page 2: Table Of Contents

    ORDERING PARTS..................………… 29 BEFORE YOU BEGIN ® Thank you for selecting the MARCY MWM-1860 HOME GYM by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.

  • Page 3: Important Safety Notices

    IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.

  • Page 4: Warning Label Placement

    WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Middle Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.

  • Page 5: Hardware Identifier

    HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
  • Page 6 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
  • Page 7 HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

  • Page 8: Assembly Instructions

    ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Middle Stabilizer (#2) on flat surface. B.) Attach the Base Frame (#3) to the front of Middle Stabilizer.
  • Page 9 STEP 2 (See Diagram 2) A.) Insert the two Guide Rods (#11) into the holes on the Middle Stabilizer (#2). Secure each Guide Rod with one M10 x 1” Allen Bolt (#81) and two  ¾” Washers (#91) from the bottom. Slide two Ø 2 ¼” x 1” Guide Rod Rubber Bumpers (#39) onto the two Guide Rods from top to bottom.
  • Page 10 DIAGRAM 2...
  • Page 11 STEP 3 (See Diagram 3) A.) Slide 14 Weight Plates (#42) onto the Guide Rods (#11). Make sure the deep grooves on the Weight Plates all face the back of the machine and downward. B.) Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole. Slide the Selector Stem (#41) onto the Guide Rods.
  • Page 12 STEP 4 (See Diagram 4) A.) Place the Upper Frame (#1) onto the Vertical Frame (#4). B.) Attach the brackets on the Upper Frame to the two Guide Rods. Secure the Guide Rods to the brackets with two M10 x 1” Allen Bolts (#81) and Ø ¾” Washers (#91). C.) Secure the Upper Frame to the Power Station Vertical Frame (#26) with two M10 x 2 3/8”...
  • Page 13 DIAGRAM 4...
  • Page 14 STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 8 ½” Front Press Axle (#19), two Ø 1” Large Washers (#96), and two M10 Aircraft Nuts (#97). Do not over tighten the Nuts.
  • Page 15 DIAGRAM 5...
  • Page 16 STEP 6 (See Diagram 6) A.) Attach the Left Dip Support (#28) into Right Dip Support (#27) behind the Power Station Vertical Frame (#26). B.) Attach the holes on the bracket of Left & Right Dip Support to the hole on the Vertical Frame.
  • Page 17 DIAGRAM 6...
  • Page 18 STEP 7 (See Diagram 7) A.) Attach one Swivel Pulley Bracket (#17) to the open bracket on the back of Vertical Frame (#4). Secure it with one M10 x 2 ½” Allen Bolt (#76), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#97). Do not over tighten the Nut and Bolt. Make sure the Swivel Pulley Bracket can swivel freely.
  • Page 19 STEP 8 (See Diagram 8) A.) Attach the Power Station Arm Pads (#35) to the Right & Left Dip Support (#27 & #28). Secure each Arm Pad with two M8 x 2 ¾” Allen Bolts (#84) and two Ø 5/8” x 1” Curved Washers (#94).
  • Page 20 STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 127 ½” Upper Cable (#56) to the front open bracket under the Upper Frame (#1). B.) Attach a Pulley (#40) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#74), two Ø...
  • Page 21 DIAGRAM 9...
  • Page 22 STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Hook one end of the 98” Butterfly Cable (#57) to Right Butterfly (#10). B.) Draw the Cable towards the right open Swivel Pulley Bracket (#17). C.) Attach a Pulley (#40) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#74), two  ¾” Washers (#91), and one M10 Aircraft Nut (#97).
  • Page 23 STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 159” Lower Cable (#58) to the opening bracket on Leg Developer (#7). B.) Attach a Pulley (#40) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#76), two ...
  • Page 25 STEP 12 (See Diagram 12) A.) Connect Lat Bar (#14) to the Upper Cable (#56) with two Hooks (#63) and one 15-link Chain (#55) when doing Lat Pull exercises. B.) Connect Shiver Bar (#15) to the Lower Cable (#33) use the two Hooks and the 15-link Chain from Lat Bar when doing Arm Curl exercises C.) Replace Shiver Bar with the Ankle Strap (#66) or Single Handle (#61) to the Lower Cable for various exercises.
  • Page 26 STEP 13 (See Diagram 13) A.) Do not tighten the Bolts until instructed to do so. B.) Attach one Weight Stack Bracket (#100) to the bracket on Upper Frame (#1). Attach the top of Weight Stack Cover (#101) to the Weight Stack Bracket. Secure them to together with one M8 x 5/8”...
  • Page 27 Set up the Lock Combination A.) The combination is pre-set to 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and aligned to the Combination Set Up Line. C.) Pull out the shackle and turn 180 D.) Press down on the shackle. E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination.

  • Page 28: Parts List

    PARTS LIST KEY NO. DESCRIPTION Q’ty Upper Frame Ø 1” x Ø ½” Bushing Middle Stabilizer Ø 1” x 5/8” Pulley Bushing Base Frame Combination Lock Vertical Frame 2” Weight Plate Lock Pin Seat Support 15-link Chain Vertical Seat Support 127 ½”...

  • Page 29: Resistance Chart

    MWM1860 WEIGHT RESISTANCE CHART Weight Plate Front Butterfly Developer Press Pull Pulley Note: Each plate weights 10 lbs. Numbers are approximate. Actual weights may vary. Values for Butterfly are for each arm.

  • Page 30: Warranty

    ® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.

Table of Contents