Advertisement
Quick Links
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM-8900
Retain This
Manual for
Reference
08-12-05
OWNER'S
MANUAL
CORNER GYM
MWM-8900
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
MARCY
IMPEX INC.
Advertisement
Related Manuals for Impex MARCY MWM-8900
Summary of Contents for Impex MARCY MWM-8900
- Page 1 Hardware Pack Assembly Instruction MWM-8900 Parts List Resistance Chart Warranty Ordering Parts Model MWM-8900 Retain This Manual for Reference 08-12-05 IMPEX INC. OWNER'S 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 MANUAL Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
-
Page 2: Table Of Contents
BEFORE YOU BEGIN Thank you for selecting the MARCY MWM-8900 CORNER GYM by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. If you have any questions, or find there are missing or damaged parts, we guarantee you complete satisfaction through direct assistance from our factory. -
Page 3: Important Safety Notices
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. - Page 4 WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in location shown.
-
Page 5: Hardware Pack
HARDWARE PACK... - Page 6 HARDWARE PACK...
- Page 7 HARDWARE PACK...
-
Page 8: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#1) on a flat surface. Make sure there is enough space around to assemble the machine. - Page 9 STEP 2 (See Diagram 2) A.) Attach the Left Base and the Rear Base Frame (#2 & #3) to the Right Base Frame (#1). B.) Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#98), ∅ ¾” Washers (#21), and M10 Aircraft Nuts (#18).
- Page 10 STEP 3 (See Diagram 3) A.) Slide fourteen Weight Plates (#54) onto the rear set of Guide Rods (#4). Make sure the groove on the plates all face toward the front of the machine. B.) Insert a Selector Rod (#53) into the center holes. Slide a Selector Stem (#34) onto the two Guide Rods.
- Page 11 STEP 4 (See Diagram 4) A.) Do not tighten all Nuts and Bolts in this step until instructed to do so. B.) Attach the Right Vertical Frame (#5) to the Right Base Frame (#1). Secure it with two M10 x 2 ½”...
- Page 12 STEP 5 (See Diagram 5) A.) Do not tighten all Nuts and Bolts in this step until instructed to do so. B.) Place the Upper Frame (#8) onto the Right Vertical Frame (#5) and two Guide Rods (#4). Secure the Upper Frame to the Right Vertical Frame with two M10 x 2 ½” Carriage Bolts (#98), one 4 3/8”...
- Page 13 STEP 6 (See Diagram 6) A.) Securely tighten all Nuts and Bolts previously installed. B.) Attach the Right Seat Support (#10) to the Right Base Frame (#1). Secure it with one M10 x 2 ½” Carriage Bolt (#98), Ø ¾” Washer (#21), and M10 Aircraft Nut (#18). C.) Attach the Right Seat Support (#10) to the Right Vertical Frame (#5).
- Page 14 DIAGRAM 6...
- Page 15 STEP 7 (See Diagram 7) A.) Attach the Left Seat Support (#11) to the Left Base Frame (#2). Secure it with one M10 x 2 ½” Carriage Bolt (#98), Ø ¾” Washer (#21), and M10 Aircraft Nut (#18). B.) Attach the Left Seat Support (#11) to the Left Vertical Frame (#6). Secure it with two M10 x 2 ½”...
- Page 16 STEP 8 (See Diagram 8) A.) Insert the axle on the Right Butterfly (#15) through a Butterfly Adjustment Frame (#50) into the Butterfly Support Frame (#12). Secure it with one M10 x 5/8” Allen Bolt (#93), Ø ¾” Washer (#21), and Lock Ring (#33). B.) Thread a T-shaped Pull Pin (#66) into the hole on the Right Butterfly from the bottom.
- Page 17 STEP 9 (See Diagram 9) A.) Attach the Vertical Press Base (#23) to the pivot on the Rear Vertical Frame (#7). Secure it with one Axle (#59), two Ø ¾” Washers (#21), and two M10 Aircraft Nuts (#18). B.) Attach one Vertical Press Arm (#24) to the Vertical Press Base. Secure it with two M10 x 2 ½”...
- Page 18 CABLE LOOP DIAGRAM...
- Page 19 STEP 10 (See Cable Loop Diagram & Diagram 10) A.) Attach the 102” Upper Cable (#36) to the front opening on the Upper Frame (#8). Attach a Pulley (#64) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#96), two Pulley Bushings (#63), and one M10 Aircraft Nut (#18).
- Page 20 DIAGRAM 10...
- Page 21 STEP 11 (See Cable Loop Diagram & Diagram 11) A.) Clip one end of the 76” Butterfly Cable (#37) to the slot on the Left Butterfly Adjustment Frame (#50). Draw the Cable through the slot then to the open Swivel Pulley Bracket (#49). B.) Attach a Pulley (#64) to the bracket.
- Page 22 STEP 12 (See Cable Loop Diagram & Diagram 12) A.) Attach the 146” Lower Cable (#35) to the lower opening on the Leg Developer (#26). Attach a Pulley (#64) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#96), two Pulley Bushings (#63), and one M10 Aircraft Nut (#18).
- Page 23 DIAGRAM 12...
- Page 24 STEP 13 (See Diagram 13) A.) Attach the 49” Front Press Cable (#38) to the small opening on the Right Vertical Frame (#5). Secure the head of the Cable to the small opening with one M10 x 2 3/8” Allen Bolt (#96), two Ø...
- Page 25 STEP 14 (See Diagram 14) A.) Attach a Short Chain (#88) to the open bracket on the Rear Vertical Frame (#7). Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#21), and one M10 Aircraft Nut (#18). B.) Connect the 94”...
- Page 26 DIAGRAM 14...
- Page 27 STEP 15 (See Diagram 15) A.) Attach the 216” Leg Press Cable (#40) to the bracket on the back of Leg Press Frame (#25). Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#21), and one M10 Aircraft Nut (#18).
- Page 28 STEP 16 (See Diagram 16) A.) Place a Seat Pad (#42) onto the Seat Incline Adjustment Frame (#27). Secure it with two M8 x 1 5/8” Allen Bolts (#102) and ∅ 5/8” Washers (#20). Insert the Frame into the opening on the Left Seat Support (#11).
- Page 29 STEP 17 (See Diagram 17) A.) Attach the Backrest Board (#41) to the Right & Left Vertical Frames (#5 & #6). Secure each Board with two M8 x 2 ½” Allen Bolts (#101) and Ø 5/8” Washers (#20). B.) Place the Seat (#42) onto the Right Seat Support (#10). Secure it with two M8 x 2 ½” Allen Bolts (#101) and Ø...
-
Page 30: Parts List
PARTS LIST KEY NO. DESCRIPTION Q’ty Arm Curl Handle Right Base Frame Arm Curl Handle Bar Left Base Frame Vinyl Foam Roll Rear Base Frame Axle Guide Rod L-shaped Cable Retainer Right Vertical Frame 2” Square End Cap Left Vertical Frame Weight Selector Pin Rear Vertical Frame Pulley Bushing... -
Page 31: Resistance Chart
MWM-8900 WEIGHT RESISTANCE CHART WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Leg Press 110 130 150 Front Press 110 125 Vertical Press WEIGHT PLATE Station Low Pulley 115 125 135 145 155 165 Lat Pull 105 115 125 135 145 Butterfly 101 108 115 Leg Press... -
Page 32: Warranty
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.