1. Manuals
  2. Brands
  3. Impex Manuals
  4. Home Gym
  5. MARCY MWM 1801
  6. Owner's manual

Impex MARCY MWM 1801 Owner's Manual

Impex owner's manual home gym mwm 1801
Hide thumbs
Table of Contents

Advertisement

Quick Links

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 1801
Retain This
Manual for
Reference
08-18-03
OWNER'S
MANUAL
MARCY HOME GYM
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
MWM 1801

Advertisement

Table of Contents
loading

Related Manuals for Impex MARCY MWM 1801

Summary of Contents for Impex MARCY MWM 1801

  • Page 1 Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM 1801 Retain This Manual for Reference 08-18-03 OWNER'S MANUAL MARCY HOME GYM MWM 1801 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com...

  • Page 2: Table Of Contents

    ORDERING PARTS...………… 28 BEFORE YOU BEGIN Thank you for selecting the MARCY MWM 1801 HOME GYM by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.

  • Page 3: Important Safety Notices

    OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS.

  • Page 4: Hardware Pack

    HARDWARE PACK...
  • Page 5 HARDWARE PACK...

  • Page 6: Assembly Instructions

    ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Left Base Frame (#3) to the Right Base Frame (#1). Secure them with one Bracket (#47), two M10 x 2 ½”...
  • Page 7 STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10 x 2 ½” Carriage Bolts (#82), Do not tighten the Nuts and Bolts yet. B.) Attach the Right Seat Support (#8) to the Right Base Frame (#1). Secure it with one M10 x 2 ½”...
  • Page 8 STEP 3 (See Diagram 3) A.) Align four 2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame (#1). Insert four Guide Rods (#5) through the Rubber Bumpers into the holes on the Right Base Frame. Slide two Selector Stems (#35) onto the Guide Rods. Insert a Selector Rod (#24) through the hole on each Selector Stem.
  • Page 9 DIAGRAM 3...
  • Page 10 STEP 4 (See Diagram 4) A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#82), B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left Vertical Beam.
  • Page 11 DIAGRAM 4...
  • Page 12 STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure it with a M10 x 9 ¼” Axle (#50), two B.) Attach the two Front Presses (#16) to the Front Press Base (#15). Secure each Front Press with two M10 x 2 ½”...
  • Page 13 STEP 6 (See Diagram 6) A.) Insert the axle on the Left Butterfly (#12) through the hole on the Left Upper Frame (#11) from the bottom up. Slide a onto the Axle. Align the holes and secure the Ring with a M6 x 1 5/8” Hex Bolt (#87) and M6 Aircraft Nut (#91).
  • Page 14 Cable Loop Diagram for Butterfly Station...
  • Page 15 Cable Loop Diagram for Bench Press Station...
  • Page 16 STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the two Swivel Pulley Brackets (#42) to the Left Upper Frame (#11). Secure each Bracket with one M12 x 4 3/8” Allen Bolt (#76), two Nut (#89). NOTE: Do not over tighten the Bolt. Make sure the Bracket is able to swivel. B.) Attach one end of the 83”...
  • Page 17 STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach a Chain (#51) to the Left Vertical Beam (#4). Secure it with one M10 x 1 3/8” Allen Bolt (#83), two end of the 136” Butterfly Support Cable (#31) to the Chain using a C-clip (#63). NOTE: After complete installing all the cables, check the tightness of the cable loop system.
  • Page 18 STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the140” Leg Press Cable (#28) to the opening hole on the Left Seat Support (#14), underneath the rubber bumper. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ¾”...
  • Page 19 DIAGRAM 9...
  • Page 20 STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 114” Upper Cable (#26) to the front opening on the Right Upper Frame (#6). NOTE: The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley (#65) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two 5/8”...
  • Page 21 STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 39” AB Cable (#30) to the opening on the Right Vertical Beam (#2). Attach a Pulley to the opening. Secure the Pulley with one M10 x 2 3/8” Allen Bolt (#79), two 5/8”...
  • Page 22 DIAGRAM 11...
  • Page 23 STEP 12 (See Diagram 12) A.) Now move the machine to its final position. After installing the weight stack, it will be too heavy to move. Check and tighten all Nuts and Bolts previously installed. B.) Install 9 Weight Plates (#36) to each set of Guide Rods (#5). To install the plate, lift up the Selector Rod in the center, hold the plate at an angle and place between the two Guide Rods then drop it down.
  • Page 24 STEP 13 (See Diagram 13) A.) Insert one Foam Tube (#34) halfway through the hole on the Right Seat Support (#8). Insert one Foam Tube (#34) halfway through the hole on the Leg Developer (#9). Push four Foam Rolls (#38) onto the Tubes from both sides. Plug the Foam Roll End Caps (#74) into the ends. B.) Attach the Lat Bar (#20) to the Chain (#51) using a C-clip (#63).
  • Page 25 STEP 14 (See Diagram 14) A.) Attach a Backrest Board (#23) to the Left Vertical Beam (#4). Secure it with two M8 x 2 1/8” Allen Bolts (#84) and B.) Place the Seat (#22) onto the Left Seat Support (#14). Secure it with two M8 x 2 1/8” Allen Bolts (#84) and two C.) Attach the Leg Press Plate (#19) to the Leg Press Frame (#17).

  • Page 26: How To Use

    HOW TO USE How to use the quick release connector. Insert The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes. Chain Push down the Clip to secure.

  • Page 27: Parts List

    1 ½” Square End Cap 1 ¾” Square Sleeve 2” Square End Cap (Impex Logo) 1 ¾” Square End Cap (Impex Logo) 19 1 ½” Square End Cap (Impex Logo) 2 Foam Roll End Cap M10 x 8 ¼” Allen Bolt M12 x 4 3/8”...

  • Page 28: Resistance Chart

    MWM 1801 Weight Resistance Chart Station Low Pulley Lat Pull Ab Strap Butterfly Leg Press Front Press *Each plate weights 10 lb. *Resistance measured in pounds. *Numbers are approximate. Actual number may vary. Weight Plate...

  • Page 29: Warranty

    IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used for commercial or rental purposes.

Table of Contents