Page 1
NOTE: Please read all instructions carefully before using this product MARCY HOME GYM Table of Contents W/BOXING BAG Safety Notice MP-3205 Hardware Identifier Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model PM-3205 Retain This Manual for Reference 110601 ®...
TABLE OF CONTENTS BEFORE YOU BEGIN..................………… 1 IMPORTANT SAFETY NOTICES..............……….. 2 HARDWARE PACK………..…..............……….. 4 ASSEMBLY INSTRUCTIONS.................……….. 7 PARTS LIST……………………………………………………………………………….. EXPLODED DIAGRAM…………………………………………………………………… RESISTANCE CHART…………...............……… 30 WARRANTY....................…………. 31 ORDERING PARTS..................………… 31 BEFORE YOU BEGIN Thank you for selecting the PLATINUM MARCY PM-3205 HOME GYM ®...
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Push two Ø...
Page 10
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Front Vertical Frame (#3) onto the Base Frame (#5). Secure with two M10 x 3 ½” Carriage Bolts (#78), one 5 ½” x 2” Bracket (#21), two Ø ¾” Washers (#84), and two M10 Aircraft Nuts (#83).
Page 11
STEP 3 (See Diagram 3) A.) Slide the 14 Weight Plates (#34) onto the Guide Rods (#13). Make sure the deep grooves on the Plates are all facing down and toward back of the machine. If the locking holes on the guide rods are more than 2-3 inches from the upper most, then you have installed the Guide Rods upside down.
Page 13
STEP 4 (See Diagram 4) A.) Attach the Front Press Base (#6) to the Upper Frame (#4). Secure it with one 6 1/8” Front Press Axle (#37), one Ø ¾” Washer (#84), one Ø ¾” Lock Washer (#88), one M10 x 1” Allen Bolt (#73), and one Ø...
Page 15
A.) Attach the Main Seat Support (#1) to the Front Vertical Frame (#3). Secure it with two M10 x 3 ½” Carriage Bolts (#78), one 4 ¾” x 1 ¾” Bracket (#22), two ¾” Washers (#84), and two M10 Aircraft Nuts (#83). B.) Attach the Seat Bracket (#20) onto the Main Seat Support.
Page 17
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach the 118” Upper Cable (#59) to the opening on the front of the Upper Frame (#4). Note: The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69), two Ø...
Page 19
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach one end of the 122” Butterfly Cable (#61) onto the hook on the Right Butterfly Base (#7). B.) Draw the Cable to the right Swivel Pulley Bracket (#26). C.) Attach a Pulley (#62) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø ¾”...
Page 21
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach the 165” Lower Cable (#60) to the opening on the bottom of the Leg Developer (#11). B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69), two Ø...
Page 23
STEP 9 (See Diagram 9) A.) Attach a Chain (#66) to the Upper Cable (#59) by using a Hook (#67). Attach the Lat Bar (#17) to the Chain by using another Hook. B.) Remove Lat Bar from the Chain. Remove and attach the Chain to the Lower Cable (#60) by using the Hook (#67).
Page 24
Step 10 (See Diagram 10) A.) Attach the Speed Bag Board (#104) to Speed Bag Hanging Frame (#101). Secure it with four M8 x 1 1/8” Allen Bolts (#70), eight Ø 5/8” Washers (#86), and four M8 Aircraft Nuts (#115). B.) Use the Locking Clip (#112) to secure the Speed Bag (#106) to the Speed Bag Board.
Page 25
Step 11 (See Diagram 11) A.) Slide the Speed Bag Hanging Frame (#101) onto the Hanging Frame (#100) from bottom. Use the M18 Lock Knob (#54) to lock the Speed Bag Hanging Frame at desired height. B.) Attach the Hanging Frame to Front Vertical Frame (#3) and Upper Frame (#4). Secure them together with two M10 x 4 ¾”...
Page 26
Step 12 (See Diagram 12) A.) Thread the Heavy Bag Hanging Bolt (#102) through Hang Frame (#100) from bottom and secure with one Ø 1” Washer (#85) and M12 Aircraft Nut (#91). B.) Hook four 7-link Chains (#111) to the Heavy Punch Bag (#105). Attach the four Chains to the Hanging Bolt by using a Hook (#67).
Page 27
Combination Lock Set Up Instruction The Lock is set at the manufacturer to the open at 0-0-0 (all zeros are positioned in the middle). It is recommended to change the combination to ensure safety. Please follow the below steps to change the combination: 1.
PARTS LIST KEY NO. DESCRIPTION Q’ty 2 3/8” x 2” Sleeve Main Seat Support Handle Grip Rear Base Frame Ø 2” End Cap Front Vertical Frame Ø 1 ¾” x 1 5/8” Rubber Bumper 1 Upper Frame 1” x 2” End Cap Base Frame 2”...
Page 29
PARTS LIST KEY NO. DESCRIPTION Q’ty M6 Aircraft Nut M5 Aircraft Nut M12 Aircraft Nut M8 x ¾” Allen Bolt L-shaped Lock Pin M6 x 5/8” Philips Screw Rubber Spacer Ø 1 1/8” x 3 ¼” Bushing M10 x 6 ¾” Allen Bolt Combination Lock Heavy Bag Base Frame Hanging Frame...
PM3205 WEIGHT RESISTANCE CHART WEIGHT PLATE Station Front Press Lat Pull Butterfly Low Pulley Leg Developer WEIGHT PLATE Station Front Press Lat Pull Butterfly Low Pulley Leg Developer Note: Each plate weights 10 lbs. Numbers are approximate. Actual weights may vary. Values for Butterfly are for each arm.
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.