Table of Contents
Advertisement
NOTE:
Please read all instructions
carefully before using this
product
Safety Notice
Hardware Identifier
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MACH IV
Retain This
Manual for
Reference
06-20-01
OWNER'S
MANUAL
MARCY MACH IV
HOME GYM
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
Advertisement
Table of Contents
Related Manuals for Impex MACH IV
Summary of Contents for Impex MACH IV
-
Page 1: Home Gym
NOTE: Please read all instructions carefully before using this product Safety Notice MARCY MACH IV Hardware Identifier HOME GYM Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MACH IV Retain This Manual for Reference 06-20-01 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746... -
Page 2: Table Of Contents
WARRANTY....................… 21 ORDERING PARTS..................21 BEFORE YOU BEGIN Thank you for selecting the MARCY MACH IV PERSONAL TRAINER by IMPEX FITNESS PRODUCTS. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction. -
Page 3: Important Safety Notices
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. -
Page 5: Assembly Instructions
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Main Base Frame (#1), Front Stabilizer (#4) and Front Base Frame (#2) on the floor. Secure the three pieces together with two M10 x 2 ¾”... - Page 6 A.) Align two Rubber Bumpers (#81) to the holes on the Main Base Frame (#1). Push two Guide Rods (#9) into the holes. Install 19 Weight Plates (#62). To install the plates, hold the plate at an angle and place between the two guide rods then drop it down. Make sure the grooves on the plastic covers all face up.
- Page 7 A.) Attach the Butterfly Support Frame (#14) to the front of the Front Vertical Beam (#6). Attach the Butterfly Pulley Support (#15) to the back of the Front Vertical Beam (#6). Secure them with two M10 x 3” Carriage Bolts (#102), 3/4”...
- Page 8 A.) Attach Foot Support (#11) to the Main Base Frame (#1). Secure it with one M10 x 2 ¾” Carriage Bolt (#103), 4” x 2” Bracket (#76), 3/4” Washer (#127), and M10 Aircraft Nut (#132) to the rear hole. Secure the front hole with one M10 x 2 ½” Allen Bolt (#114) and 3/4”...
- Page 9 A.) Attach the Bench Press Base (#13) to the opening on the Rear Vertical Beam (#5). Carefully place two 1 ½” Washers (#94) in between the Base (#13) and the Vertical Beam (#5). Align the holes and insert a 1” x 8” Axle (#33). Secure both sides with two 1 ½...
- Page 10 A.) Insert three Foam Roll Tubes (#27) halfway through the holes on the Leg Developer (#26). Push six Foam Rolls (#69) onto the Tubes from both sides. Close the ends with six 1” End Caps (#89). B.) Attach the Vertical Backrest Board (#38) to the Front Vertical Beam (#6). Secure it with two M8 x 2 ½”...
- Page 11 STEP 7 (See Diagram 7 & 8) A.) Attach one end of the 143” Butterfly Cable (#46) to the Clip on the Butterfly Pulley Bracket (#16) on the right side. Draw the Cable to the Butterfly Pulley Support (#15). Install a Pulley...
- Page 12 (#73). Secure it with a M10 x 1 ¾” Allen Bolt (#105), two ¾” Washers (#127), and one M10 Aircraft Nut (#132). B.) Pull the Cable downward and install a Pulley (#73) and Single Floating Pulley Bracket (#36). Secure it with a M10 x 1 ¾” Allen Bolt (#105), two ¾”...
- Page 13 A.) Attach the 121” Upper Cable (#42) to the front of the Upper Frame (#7). Install a Pulley (#73). Secure it with one M10 x 2 ½” Allen Bolt (#114), two 3/8” Bushings (#72), and one M10 Aircraft Nut (#132). Make sure the Rubber ball on the Cable is underneath the Frame. Slide the Bolt on the Cable to the other end.
- Page 14 one M10 Aircraft Nut (#132). Use Quick Release Connector and Clip (see How To Use) to connect Ab Strap (#65) to the end of Cable (This is optional). B.) Install a Small Pulley Wheel (#61) to the bracket behind the opening on the Front Vertical Beam.
- Page 15 A.) Attach one end of the 78” Bench Press Cable (#44) to the Single Floating Pulley Bracket (#36) previously installed in STEP 7B. Secure it with a M10 x ¾” Allen Bolt (#116), two 3/4” Washers (#127) and a M10 Aircraft Nut (#132). B.) Draw the Cable downward to the first bracket on the Main Base Frame (#1).
- Page 16 A.) Attach the Ball-end of the 174” Lower Cable (#43) to the Swivel Frame (#10) on the Main Base Frame (#1). Install a Pulley (#73) and secure it with a M10 x 1 ¾” Allen Bolt (#105), two ¾” Washers (#127), one L-shaped Bracket (#104), and one M10 Aircraft Nut (#132). B.) Pull the Cable upward to the Flat Double Floating Pulley Bracket (#37) previously installed in STEP 9D.
-
Page 17: Parts List
B.) Attach the Weight Stack Covers (#50) to the machine and secure it with four 3/4” Washers (#127) and M10 x 5/8” Bolts (#108). DIAGRAM 13 PARTS LIST Rear Base Frame KEY NO. DESCRIPTION Q’ty Front Base Frame Rear Stabilizer... - Page 18 Front Stabilizer 1 ½” Bushing Rear Vertical Beam Selector Stem Front Vertical Beam Ab Strap Upper Frame Ankle Strap Top Socket Assembly Single Handle Guide Rod Foam Grip Swivel Frame Foam Roll Foot Support 1” Bushing Bench Press Frame 5/8” Bushing Bench Press Base 3/8”...
- Page 19 M8 x 5/8” Allen Bolt ¾” Washer M6 x 5/8” Allen Bolt 5/8” Washer ½” Philips Head Screw ½” Washer Cone Shape Cap M12 Aircraft Nut M10 Aircraft Nut M5 x 5/16” Philips Head Screw L Shaped Pin Weight Selector Pin 6 ¼”...
-
Page 20: How To Use
HOW TO USE How to use the quick release connector. The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes. Chain Insert Push down the Clip to secure. -
Page 21: Resistance Chart
MACH IV WEIGHT RESISTANCE CHART Plat High Butterfl Bench Curl Pulley Pulley Station Press * Numbers are approximate. Actual weights may vary. -
Page 22: Warranty
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.