Table of Contents
Advertisement
Index
R
raw attribute value ................................... 5-48
READ BUFFER ...................................... 5-73
read circuit............................................... 4-10
READ DMA............................................ 5-69
READ DMA (EXT) ................................ 6-12
READ DMA EXT ................................. 5-111
READ DMA EXT ................................... 6-12
READ LOG EXT .................................. 5-114
READ MULTIPLE ................................. 5-63
READ MULTIPLE (EXT)...................... 6-12
READ MULTIPLE EXT.............. 5-113, 6-12
READ NATIVE MAX ADDRESS....... 5-103
READ NATIVE MAX ADDRESS
EXT ................................................... 5-112
READ SECTOR(S)................................. 5-21
READ SECTOR(S) (EXT) ..................... 6-12
READ SECTOR(S) COMMAND
protocol.............................................. 5-130
READ SECTOR(S) EXT ............. 5-110, 6-12
READ VERIFY SECTOR(S) ................. 5-26
READ VERIFY SECTOR(S) EXT....... 5-124
read/write circuit .........................2-3, 4-3, 4-9
read/write circuit block diagram................ 4-9
read/write preamplifier (PreAMP) ............ 4-9
read-ahead cache ..................................... 6-12
read-ahead cache system ........................... 1-3
RECALIBRATE ..................................... 5-20
recommended power-off sequence.......... 1-13
recommended series termination for
ultra DMA.......................................... 5-148
reliability ................................................. 1-11
reset ........................................................... 6-8
reset response .......................................... 6-20
response to
diagnostic command .............................. 6-6
hardware reset................................. 6-3, 6-4
power-on ......................................... 6-2, 6-3
software reset ......................................... 6-5
ripple.......................................................... 1-6
S
sector count register .................................. 5-9
sector number register ............................. 5-10
sector slip processing............................... 6-10
SECURITY DISABLE PASSWORD... 5-101
SECURITY ERASE PREPARE ............. 5-97
SECURITY ERASE UNIT ..................... 5-98
SECURITY FREEZE LOCK.................. 5-99
SECURITY SET PASSWORD............... 5-93
SECURITY UNLOCK............................ 5-95
SEEK....................................................... 5-27
seek operation.......................................... 4-18
IN-4
selective self-test feature flag ..................5-57
selective self-test log data structure .........5-56
selective self-test pending time................5-57
self-calibration ...........................................4-7
self-calibration content ..............................4-7
self-diagnosis .............................................1-3
self-test execution status .................5-49, 5-55
self-test index...........................................5-55
self-test number .......................................5-55
sensing and compensating for
external force..........................................4-7
sequential hit............................................6-16
series termination required for ultra
DMA ..................................................5-148
service area ................................................3-6
service life................................................1-11
servo burst capture circuit........................4-13
servo circuit ...............................................4-3
servo control ............................................4-12
servo control circuit .................................4-12
servo frame format...................................4-17
servo mark ...............................................4-17
SET FEATURES ..............................5-89, 6-9
SET MAX..............................................5-104
SET MAX ADDRESS...........................5-104
SET MAX ADDRESS EXT ..................5-118
SET MAX FREEZE LOCK ..................5-108
SET MAX LOCK ..................................5-106
SET MAX SET PASSWORD ...............5-105
SET MAX UNLOCK ............................5-107
SET MULTIPLE MODE.........................5-67
shock and vibration..................................1-10
shock and vibration specification ............1-10
signal assignment on the connector ...........5-3
SLEEP ..............................................5-40, 6-9
sleep mode .................................................6-8
slope of an input voltage at rise .................1-6
SMART ...................................................5-41
SMART error logging..............................5-52
SMART self-test......................................5-55
SMART self-test log data format.............5-55
spare area ...................................................6-9
specification...............................................1-4
specification summary ...............................1-4
spindle........................................................4-2
spindle motor .............................................2-2
spindle motor control...............................4-19
spindle motor control circuit....................4-13
spindle motor driver circuit .......................4-3
stable rotation mode.................................4-19
STANDBY .......................................5-36, 6-9
STANDBY command................................6-8
STANDBY IMMEDIATE................5-33, 6-9
STANDBY IMMEDIATE command........6-8
C141-E250
Advertisement
Table of Contents
