Husqvarna 1650EXLT Operator's Manual

Walk-behind snow throwers
Hide thumbs

Advertisement

Operator's Manual
1650EXLT
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.
Please read the owner's manual carefully and make sure you
115 49 77-27 Rev. 1
English
understand the instructions before using the machine.

Advertisement

loading

  Related Manuals for Husqvarna 1650EXLT

  Summary of Contents for Husqvarna 1650EXLT

  • Page 1 Operator’s Manual 1650EXLT Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Please read the owner's manual carefully and make sure you 115 49 77-27 Rev.
  • Page 2: Safety Rules

    IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions.
  • Page 3: Maintenance And Storage

    Clearing a Clogged Discharge Chute 6. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect chute is the most common cause of injury associated with the spark plug wire and keep the wire away from the snow throwers.
  • Page 4: Table Of Contents

    CONGRATULATIONS on your purchase of a new snow PRODUCT SPECIFICATIONS thrower. It has been designed, engineered and man u - fac tured to give best possible dependability and per for - Gasoline Capacity 3.2 Quarts (3,03 Liters) mance. and Type: Unleaded Regular only Should you experience any problem you cannot easily Oil Type...
  • Page 5 PARTS PACKED SEPARATELY IN CARTON (1) MULTI- WRENCH (180684) (1) POWER CORD SAFTEY IGNITION KEY (S) (198563) (193071) (1) AUGER CONTROL ROD (1) DISCHARGE CHUTE EXTRA SHEAR BOLTS AND NUTS (6) SHOULDER (6) LOCKNUTS BOLT 1/4-20 x 1-3/4 1/4-20 (192090) (73800400) ROTATOR HEAD MOUNTING (3) RETAINER...
  • Page 6: Assembly / Pre-Operation

    ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product. Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes.
  • Page 7 ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) (See Figs. 3 and 4) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. The traction drive control rod is installed on the snow Slide straight rod end through the small hole in the thrower.
  • Page 8: Assembly / Pre-Operation

    ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR INSTALL CHUTE DEFLECTOR REMOTE CONTROL HEAD (See Fig. 7) (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with NOTE: The multi-wrench provided in your parts bag may 5/16-18 carriage bolt and 5/16-18 locknut as shown.
  • Page 9: Operation

    OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product.
  • Page 10 OPERATION GAS O LINE ELECTRIC AUGER DISCHARGE CHUTE CONTROL LEVER FILLER CAP START CONTROL DRIVE SPEED DEFLECTOR BUTTON TRACTION LEVER CON TROL LEVER REMOTE DRIVE MUF FLER CONTROL LEVER RECOIL CONTROL (AUXILIARY) LEVER STARTER HANDLE CHOKE CON- TROL CHUTE DE FLEC TOR PRIM ER LH TURN TRIGGER...
  • Page 11: Snow Thrower

    OPERATION To operate the height adjust mechanism, using your TRANSPORT AND HEIGHT ADJUSTMENT OF foot, push down on the pedal, tilt the unit to align SNOW THROWER the pins with the selected height position and slowly release foot pressure until the pins are seated in the TO TRANSPORT (See Figs.
  • Page 12 OPERATION TO USE FUEL SHUT-OFF VALVE (See Fig. 14) WARNING: If the discharge chute or au- The fuel shut-off valve is located beneath the fuel tank on ger become clogged, shut-off en gine the engine. Always op er ate the snow thrower with the fuel and wait for all moving parts to stop.
  • Page 13 OPERATION NOTE: When both traction drive and auger control levers When cleaning, repairing, or in spect ing, make are engaged, the traction drive control lever will lock the certain all controls are disengaged and the au- auger control lever in the engaged position. This will allow ger/impeller and all moving parts have stopped.
  • Page 14: Before Starting The Engine

    OPERATION 1. Shut off engine and wait for all moving parts to stop. WARNING: Wipe off any spilled oil or 2. Adjust skid plates by loosening the hex nuts, then mov- fuel. Do not store, spill or use gasoline ing skid plate to desired position. Be sure both plates near an open flame.
  • Page 15: Operation

    OPERATION COLD START - ELECTRIC STARTER IF RECOIL STARTER HAS FROZEN 1. Insert safety ignition key (tied to recoil start cord) into If the recoil starter has frozen and will not turn the engine, ignition slot until it clicks. DO NOT turn the key. Keep proceed as follows: the extra safety ignition key in a safe place.
  • Page 16: Maintenance Schedule

    MAINTENANCE LUBRICATION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items ➀ that have been sub ject ed to operator abuse or negligence. SAE 30 Motor Oil To receive full value from the warranty, operator must ➁...
  • Page 17 MAINTENANCE SNOW THROWER TO CHANGE ENGINE OIL Determine temperature range anticipated before next oil Always observe safety rules when performing main te nance. change. All oil must meet API service classification SG–SL. TRACKS • Be sure snow thrower is on level surface. •...
  • Page 18: Service And Adjustments

    SERVICE AND ADJUSTMENTS To replace the capscrew/shear bolts: WARNING: To avoid serious injury, before per- 1. Disengage all controls and move throttle control to forming any service or ad just ments: STOP position. Wait for all moving parts to stop. 1.
  • Page 19 SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 27) 7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around The auger and traction drive belts are not adjustable. If the pulleys. belts are damaged or begin to slip from wear, they should be replaced.
  • Page 20 SERVICE AND ADJUSTMENTS TO ADJUST TRACTION BELT AND AUGER BELT TO REMOVE TRACKS (See Fig. 28) TENSION • Remove the klik pin and remove track from axle. If the traction or auger belt is slipping because it is not tight enough when engaged, the tension can be increased by HOLE adjusting the spring location in the control rod.
  • Page 21 SERVICE AND ADJUSTMENTS STEERING BELLCRANK STEERING STEERING BELLCRANK YOKE VERTICAL SURFACE STEERING YOKE STEERING CLUTCH HIGH POSITION FIG. 32 FIG. 35 Adjust the position of the steering bellcrank by turning NOTE: Figure 33 shows the bellcrank positioned too low, the adjuster to raise or lower the bellcrank. When the causing hard disengagement or self-disengagement while bellcrank is positioned correctly, replace the plastic driving.
  • Page 22: Storage

    STORAGE Immediately prepare your snow thrower for storage at • Empty the fuel tank by starting the engine and letting it run until the fuel lines and car bu re tor are empty. the end of the season or if the unit will not be used for 30 days or more.
  • Page 23: Troubleshooting

    TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so equipped) 1. Turn fuel shut-off valve to OPEN position. in OFF position. 2. Safety ignition key is not inserted. 2.
  • Page 24 (a) Engines and Attachments.Except where otherwise indicated on Exhibit A, all Engines and Attachments are not covered by this Limited Warranty. In most cases, these items are NOT manufactured by Husqvarna in which case they may be covered separately by their respective manufacturer's warranties if one is provided and included with the product at the time of purchase.
  • Page 25 10. Authorized Husqvarna Servicing Dealer/Center. In order to obtain warranty coverage it is your responsibility (at your expense) to deliver or ship your Husqvarna unit to an authorized Husqvarna Servicing Dealer/Center and arrange for pick-up or return of your unit after the repairs have been made.
  • Page 26: Warranty

    Riding Lawn Tractors: Frame, Chassis, Front Axle 5 Years No Warranty No Warranty Engine* Transmission (if made by Husqvarna/Peerless) 3 Years No Warranty No Warranty Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty...
  • Page 27 ** See reference 1 (b) of the warranty statement. RZ - Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network. EZ - One (1) Year Commercial warranty, parts & labor, with Husqvarna. Two (2) Year Consumer warranty, parts & labor, with Hydro-Gear Distributor network.
  • Page 28 08/01/2012 SR...