Table of Contents
Advertisement
Quick Links
H
R
T
all
esearch
echnologies, Inc
1163 Warner Ave.
Tustin, CA 92780
Phone: (714) 641-6607
Fax: (714) 641-6698
U
s
e
r
'
s
M
a
n
u
a
l
U
s
e
r
'
s
M
a
n
u
a
l
Model MC4-H2 and MC4-H2-SW
Dual Head KVM Switch
Control 4 Dual Video output PC's from one set of
Monitors, keyboard and mouse
UMA1091 Rev. 1.1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hall Research Technologies MC4-H2
Summary of Contents for Hall Research Technologies MC4-H2
- Page 1 Inc 1163 Warner Ave. Tustin, CA 92780 Phone: (714) 641-6607 Fax: (714) 641-6698 ’ ’ Model MC4-H2 and MC4-H2-SW Dual Head KVM Switch Control 4 Dual Video output PC's from one set of Monitors, keyboard and mouse UMA1091 Rev. 1.1...
-
Page 3: Table Of Contents
SWITCHING ... 5 SETTING THE ADDRESS OF THE MC4-H2 OR MC4-H2-SW... 5 FRONT PANEL PUSH BUTTONS: ... 6 STACKING (DAISY-CHAINING) OF MULTIPLE MC4-H2 OR MC4-H2-SW UNITS ... 7 HOT SWAPPING MICE AND KEYBOARDS ... 7 HOT SWAPPING PC’S... 8 MC4-H2-SW MONITOR FRONT PANEL MONITOR SELECTION ... 8 SPECIFICATIONS ... -
Page 4: Federal Communications Commission (Fcc) Statement
Introduction MC4-H2 allows two monitors, 1 keyboard, and 1 mouse to control 4 different PC’s or servers. By chaining up to 3 MC4- H2’s, up to 12 PC’s can be controlled. Alternatively, the MC4-H2-SW will allow the user to use one monitor at the user console and switch between them with a front panel pushbutton. -
Page 5: Supported Systems And Peripherals
• Switches two video screens from each PC to user’s console video monitors • MC4-H2-SW allows the user console to consist of one switch selectable monitor • Extremely reliable operation with proven firmware for no keyboard or mouse lock ups •... -
Page 6: Setup
Not all 4 PC ports need to be used for the MC4-H2 or MC4-H2-SW to work properly. 3. Connect a mouse to the mouse port of the master MC4-H2 or MC4-H2-SW. The Master unit is the one with PC # 1 through 4 4. -
Page 7: Operation
Example: S01 – switches to PC #1 By default, when switching, the MC4-H2 or MC4-H2-SW will not switch to a port that does not have a powered PC. (i.e. the red PWR led is not on). This behavior however, can be changed via the Serial control. -
Page 8: Front Panel Push Buttons
Let’s say you have two MC4-H2 or MC4-H2-SW units. Call them Unit A and Unit B. Unit A is set as the Master and Unit B is set as the Slave 1. If you were to change the address of Unit B to the master, Unit A will have to give up its address since Unit B has now taken the Master address. -
Page 9: Stacking (Daisy-Chaining) Of Multiple Mc4-H2 Or Mc4-H2-Sw Units
Hot swapping is not recommended but may be successfully performed. You may unplug the mouse and/or the keyboard while the MC4-H2 or MC4-H2-SW is powered up and PC’s are connected and powered on. You may then plug in the same keyboard/mouse or a different keyboard/mouse and the MC4-H2 or MC4-H2-SW will recognize the new keyboard/mouse. -
Page 10: Hot Swapping Pc's
Hot Swapping PC’s You may hot swap a PC while the MC4-H2 or MC4-H2-SW is powered up only after that PC has been turned off. After the PC has been turned off, unplug the keyboard, mouse, and video connectors of the CA10087 (4-in-1) cable then plug them into the PC you wish to insert into the MC4-H2 or MC4-H2-SW setup. - Page 12 © Copyright 2008. Hall Research Technologies, Inc. All rights reserved. esearch echnologies, 1163 Warner Ave. Tustin, CA 92780 Phone: (714) 641-6607 Fax:(714) 641-6698...
Need help?
Do you have a question about the MC4-H2 and is the answer not in the manual?
Questions and answers