Kenmore Wide LAUNDRY CENTER Use And Care Manual page 4

Place delicate items in a mesh bag.
Bleach Dispenser (some models)
Do not load items above
top of agitator vanes in wash tub.
Built-In Fabric Softener Dispenser
(some models)
Built-In Fabric Softener Dispenser
(some models)
Washing Procedures con't
• Place delicate items such as bras, shoulder pads, hosiery, and belts in a mesh
bag to prevent tangling during the wash cycle.
• Turn knit items inside out to prevent pilling.
3. Pretreat stains and heavy soil.
See Stain Removal for details.
4. Add a measured amount of detergent to the wash tub before adding the
laundry load.
Follow detergent manufacturer's directions. The amount required depends on type
of detergent, load size and soil level, and water hardness.
5. If desired, add liquid bleach to Bleach Dispenser (some models).
• Before adding the wash load, add liquid bleach to bleach dispenser located in
left front corner under the lid:
• 3/4 cup (180 ml) for small loads
• 1 cup (240 ml) for large loads
• 1-1/4 cups (300 ml) for extra-large loads.
• Then add 1 cup (240 ml) water to flush the dispenser.
• Do not use powdered bleach in the bleach dispenser.
For models without a bleach dispenser, dilute the recommended amount of
liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after
a few minutes of agitation. Do not pour bleach directly on wash load.
6. Add laundry load to washer.
• Dry load level should not be higher than the top of agitator vanes.
Do not overload the washer.
• Do not put items on top of agitator or wrap them around it. Load items evenly.
• Combine large and small items in a load. Load large items first. Large items
should not be more than half the total wash load.
• When washing a single heavy item, add 1 or 2 towels to balance the load.
7. If desired, add liquid fabric softener to Fabric Softener Dispenser (available
on some models).
For models with a built-in dispenser (see picture to the left):
1. Add liquid softener to the dispenser, following fabric softener label directions.
2. Add water to bring liquid level to fill line on dispenser cap.
3. Remove the dispenser from the agitator after each use. Rinse both cap and cup
with warm water. Replace dispenser in the agitator.
NOTE: To separate cap from cup, put thumb into dispenser and push against side of
cup (see picture to the left). After cleaning, push cap and cup firmly together. Replace
dispenser by lining up the ribs and grooves and snapping it into position.
If fabric softener builds up in or around the dispenser, clean the area with hot water.
DO NOT REMOVE SERVICE CAP FOUND INSIDE THE AGITATOR POST.
For models without a fabric softener dispenser, follow fabric softener label
directions. Add diluted fabric softener to the final rinse. Do not pour fabric softener
directly on the wash load.
8. Select cycle and settings according to type, size, and soil level of each load
See Operating Instructions for your specific model controls.
9. Start the washer.
Close the washer lid and pull out the cycle selector knob. The washer will not agitate
or spin with the lid open.
• To stop the washer, push in the cycle selector knob.
• To change a cycle, push in the cycle selector knob. Turn it clockwise to the desired
setting. Pull out the knob to restart the washer.
10. Remove items when the cycle is completed.
For your safety, the lid locks when the tub is spinning. It will remain locked for 2-3
minutes after the tub stops spinning.
• To open the lid during a spin, push in the cycle selector knob and wait about 2-
3 minutes for the lid lock to release. Do not force open the locked lid.
Place washed items in automatic dryer, line dry, or dry flat as directed by fabric care
label. Excess wrinkling, color transfer or odors may develop in items left in the washer
after the cycle has ended.
To avoid serious personal injury, do not operate washer if safety lid lock
is missing or damaged.
4