Check The Status Of Each Channel; Operations; Other Operations During Playback; Operating The Poa-3012Ci Using A Browser (Web Control) - Denon POA-3012CI - Multi-Zone Audio Distribution Power Amplifier Owner's Manual

ENGLISH
Click the menu
CHANNEL SETUP IGrExample: 1)
SYSTEM SETUP IGrExample : 2)
WARNING AND PROTECTION DATA
IGrExample : 3)
AUDIO SIGNAL AND TRIGGER
INPUT IGrExample : 4)
OPTION SETUP IGrExample: 5)
-Network SetupW - -Network Infonnation- (Grpage 15)
.OPClr:atin9 . th~. POA~3012CI .Using
a
BroW$M (Web'f;Ontroll
. -,-:- ,'•.' ,; - .,-, .'.' . . .. ~.,. '-~,-_:",</,_. - ,..:
This.function
lets
YolJ~ratethe
Pq..\-3P12CI using
Internet
Exp.lorer!>Y",. ."
g ......
;.y;·Y.c Y;,.:..,' ,... 'y;":'.'
<.•. .' . . .
Click -SAVE- when you want to save settings,
and click -LOAD- when you want to
call
settings
Becomes each operation screen
1
Check the POA-3012CI's IP Address.
2 Input the POA-3012CI's IP Address in Internet
Explorer.
For example.
if
the IP address
is
"10.3.18.90; enter
http://10.3.18.90.
3
H the top menu is displayed, click ''Setup Menu"•
4
When the ''Setup Menu" is displayed, click on the
menu you want to operate.
--------
1
Press
the DISPLAY button.
*
Zone status is indicated on the bottom line of the display.
*
Turn the SELECTjENTER knob to change the display as follows.
[
Channel No. & INPUT Line - - VOLUME CONTROL lellel
I
- .. ZONET.ON MODE - - LON CUT FILTER
-----J
Check the Status of Each Channel
Other Operations
2
Press the DISPLAY button again.
*
System status is indicated on the bottom line of the display.
*
Turn the SElfCT/ENTER knob to change the display as follows.
POWER CONFIG - - DIMMER
o
To Retum to the Regular Display
Press the
.6./RETURN
button until the display returns to normal.
o
To Adjust the Volume
Refer to "VOLUME CONTROL.:' on the "Main Setup" menu
(Grpage 13)
o
To Switch Input Setting
Refer to "INPUT SELECT" on the "Main Setup" menu (Grpage
13).
o
To Reduce the Low Frequency Volume
Refer to "LOW CUT FILTER" on the "Main Setup" menu (Grpage
13).
i
rO:' .-:
i I~·:L
Press
the ON/STANDBY button.
The power indicator flashes green and the power turns on.
*
The signal input to each channel is output from the speaker
terminal of each channel.
*
The setting status of each channel is indicated on the display.
*
Turn the SELECT/ENTER knob to change the channel displayed.
Output channel Input terminal
I I
OPERATION MODE Volume level
(No display when in "NORMAL MODE")
o~I~-DT""B-y----z-J-E-5
- D-I-J:
)1
.6./RETURN
Turning the Power On
Operation
ZONE
op,,,tioo mod, iOdi"'tO'~'~~SELECTIENTER
...
- ,;~~
..-_:..!J
o
To return to STANDBY
Press the
ON/STANDBY
button again.
The power indicator lights red.
-k
ll
" .
-When the "POWER CONFIGURATION" is set to "MASTER
TRIGGER': the device will automatically enter the standby status
when no trigger input is detected for a period of 10 minutes.
- When the "POWER CONFIGURATION" is set to "ON LINE': send
a standby command to the ETHERNET terminal or the RS-232C
terminal of the POA-3012CI.
- Power continues to be supplied to some of the circuitry even when
the power is in the standby mode. When leaving home for long
periods of time or when traveling, unplug the power cord from the
power outlet.
I
17