Summary of Contents for Denon POA-3012CI - Multi-Zone Audio Distribution Power Amplifier
Page 1
DENON MULTI CHANNEL POWER AMPLIFIER POA-3012CI Owner's Manual Bedienungsanleitung...
Page 2
FCC requirements. Modification not expressly third prong are provided for your safety. If the provided plug does not fit into approved by DENON may void your authority, granted by the FCC, to use The exclamation point within an equilateral triangle is in. tended your outlet.
Page 3
- - - - - - - - - - - - - - - - j • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. DENON Europe • Vermeiden Sie hohe Temperaturen. SIB. ausrelchende...
Using a mobile phone near this unit may result in noise. If so. move Input Connections ···· .. ······· ..· · · · 7 Thank you for purchasing this DENON product. To ensure proper the mobile phone away from this unit when it is in use. BUS INPUT Connections ···...
POA-3012CI. For details, refer to the instructions for the Before making the connections, determine the input signals and respective connection items below. output signals for each ZONE and then set up the POA-3012CI in Businput/output connections (stereo) •...
ENGLISH Co"n~ionMethoct ~8ID~ED O~ut. Speaker Connections • In BRIDGED mode, one channel is output from one ZONE. 2'Chan"fitl$ Cqnnection; Method When OutPlIttin9 Ftom • To set BRIDGED mode, select "BRIDGED" as the "OPERATION MODE" on the "Main Setup" menu. • When BRIDGED out putting a signal input to the AUDIO INPUT terminal, input to an even-numbered input ZONE, terminal.
Page 9
Tighten the speaker terminal firmly before problems in the ventilation around the set nor in the connections. inserting the banana plug. the set may be damaged. Turn the power off. then contact a DENON service center. -MIn- • Use speakers with an impedance of 4 to 16 O/ohms. Use a 8 to 16 O/ohms speaker for BRIDGED output.
Audio Source Audio Source Audio Source AUDIO AUDIO AUDIO 0t1T 0t1T 0t1T Signals input from the BUS INPUT are output from the BUS OUTPUT terminal. These signals can be output to the BUS INPUT terminal of another POA-3012CI unit.
To WAN side (@"page 15). . Built-in 100 BASE-TX switch • With the POA-3012CI. it is possible to use the DHCP and Auto IP When connecting multiple devices. we recommend a switching To LAN port functions to make the network settings automatically.
RS.2~2C C()11"ector At DC 3 - 30 V········· This connector is used for an external controller. At DC 0 V·· STANDBY If you wish to control the POA-3012CI from an external controller using the RS-232C connector, perform operation below beforehand.
For details of individual settings refer to the explanations of settings (Gf'page 13 - 16). SETUP Press the button. The POA-3012CI enters the "SETUP" mode and the first level menu is displayed. The selected item blinks. Select the required item on the menu and set it.
Page 15
ENGLISH DNetwork. DHCP Information IP Address (Gr'page Mac Address • Network Setup DHCP IPAddress (Gr'page Subnet Mask Default Gateway Primary DNS Secondary DNS Proxy Address ON - - - - - - - - 1 - Proxy Address Port Name - - - - - 1 - Proxy Name Port D Maintenance...
ENGLISH .()p.l;~n()NI\IIODE..~ channe~ineach Set$lDeo0tpufrnElthod for lONE..[Selectable Channels] [Selectable Channels] VOLUME CONTROL For details of the channels which can be set in each mode, see Sets each of the following channel pairs. INPUT SELECT [Selectable Channels in "...
Page 17
• Turns on when a signal is detected. • If no input is received for a period of 10 minutes, it switches to standby mode. • The POA-3012CI accepts +3 - 30 V trigger input. • Even when "ON LINE" or"MASTERTRIGGER" has been set. power ON/STANDBY source operation is possible by means of button.
Set the IP address at the menu "Network Setup" - i~.~~: • If the POA-3012CI is being used connected to a network without the "Network Setup". When connecting an xDSL modem or terminal adapter directly DHCP function, the network settings must be made. In this case, to the POA·3012CI, input the subnet mask indicated in the...
O~9; "';::}:i,:f..,>;:,>!,< Furthermore, updating the firmware may reset the backup data for .·~;::,':'!.·Jl· ~ nJl~.a.s.e). Only use this function if so instructed by a DENON serviceperson or tt':JJ.i.:'fi:1 the parameters, etc., set for the POA-3012CI. installer. .0< . . .:...
Zone status is indicated on the bottom line of the display. Turn the SELECTjENTER knob to change the display as follows. op,,,tioo mod, iOdi"'tO'~'~~SELECTIENTER Check the POA-3012CI's IP Address. ZONE Channel No. & INPUT Line - - VOLUME CONTROL lellel -----J ..
Page 21
ENGLISH Operate. (Example: 3] Warning and Protection Data Screen To use the web control function. set the menu "Main Setup"- "POWER (Example: 1] Channel Setup Screen CONFIGURATION" - "ON LINE" ((Fpage 14). '~[.jj. • To perform web control. you must connect a web control device such as a PC to the same network as the POA-30 12CI.
ENGLISH Troubleshooting Specifications Check the following before assuming there is a problem with the set: Rated output: 12-channel driving, NORMAL operation: 30 W x 12 ch (8 (lJohms, DIN 1 kHz with 0.7 % TH.D.) 1. Are all connections proper? 2.
Page 24
DENON www.denon.com Oenon Brand Company, O&M Holdings Inc. Printed in Japan 000511 4719004...
Page 26
Ethernet Connector type RJ-45 (lOBASE-T!lOOBASE-TX) Example Ethernet POA-30l2CI Cross cable I--J Example POA-30l2CI Ethernet Ethernet Straight Straight cable cable Communication format Communication system A half duplex Communication speed lOMbps!lOOMbps TCP port 23 (telnet) Communication port l35bytes (maximum) Communication data length - 2 -...
Page 27
"ON LINE"---Use this setting when using the POA-3012CI connected in a network. "MASTER TRIGGER" or "POWER BUTTON"--- Use this setting when not using the POA-3012CI connected in a network. This setting is reducing the power consumption in the standby mode.
Page 28
The message sent to a system(POA-3012CI) from a controller(Touch Panel etc.) Ca.MAND A command to a system is given from a controller. The message sent to a controller (Touch Panel etc.) from a system (POA-3012CI) EVENT The result is sent, when a system is operated directly and a state changes.
Page 29
The example of a * <CR> is the meaning of OxOD. SI09BUSL<CR> Select Input source "BUS L" at channel 9. S006BRIDGED<CR> Set Operation Mode to bridged mode at channel 5 & 6. SV02UP<CR> Master Volume UP at channel 2. PWOOON<CR> system PoWer ON PWOOSTANDBY<CR>...
Page 30
Others COMMAND is receivable also during transmission of EVENT. The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to the another request commands (ex. SV command). (with and RESPONSE, of minimum level of MASTER VOLUME defines "99".
Page 31
COMMAND and PARAMETER list CGHAND CHANNEL PARAME7ER function example POWER ON/STANDBY change PWOOON<CR> STANDBY PWOOSTANDBY<CR> Return PW Status PWOO?<CR> *01-12 CHANNEL VOLUME UP/DOWN , direct change to **dB SVOlUP<CR> DOWN SV01DOWN<CR> **:00 to 99 by ASCII , 90=OdB, 99=---(MIN) SV0180<CR> Return channel volume Status SV01?<CR>...
Page 33
EVENT(or RESPONSE) and PARAMETER list example function EVENT CHANNEL PARAMETER PWON<CR> POWER ON/STANDBY STANDBY PWSTANDBY<CR> *01-12 **:00 to 99 ASCII SV80<CR> CHANNEL VOLUME change 90 = OdB(MAX) 00 = -90dB 99 = ---(MIN) S002NOR<CR> 02-12 (EVEN) OPERATION MODE change S002BRI<CR> SF040FF<CR>...
Page 34
EVENT CHANNEL PARAMETER. function example TROHWARN MAIN TRANSFORMER OVER HEAT WARNING PROOTROHWARN<CR> TROHNONE MAIN TRANSFORMER OVER HEAT NONE PROOTROHNONE<CR> INOHWARN CABINET INSIDE OVER HEAT WARNING PRO 0I NOHWARN<CR> I NOHNONE CABINET INSIDE OVER HEAT NONE PROOINOHNONE<CR> MAIN TRANSFORMER TMOHTR01****** Over heat operation time (latest) PROOTMOHTR01000130<CR>...
Page 35
Finland Soundata Oy Hameentie 157 5th floor 00560 Helsinki Finland Tel: +358-(0)9-47693300 Fax: +358-(0)9-47693310 France DENON FRANCE A division of D&M France SAS Tour Ventose, 2 rue des Bourets, 92156 Suresnes Cede x, FranCE; Tel:+33(0)1-41-383230 Fax +33(011-41-380110 Germany DENON DEUTSCHLAND A division of D&M Germany GmbH An der Landwehr 19, D-41334 Nettetal, Germany...
Page 36
DENON ELECTRONICS (USA), LLC (a D&M Holdings Company) 100 Corporate Drive Mahwah, NJ 07430-2041 (800) 497-8921 (888) 544-8434 Fax DENON REGIONAL SUPER SERVICE CENTERS (Repair only-No parts orders please) PYRAMID AUDIO UNITED RADIO SERVICE AUDIO SERVICES 305 E. Braker Lane 5717 Enterprise Parkway 544 Central Dr., Suite 101...
Page 37
Except as specified below. this Warranty covers all defects in material and workmanship in this product occurring during the above warranty periods. The following are t . . · not covered by the Warranty: (I) Any product which is not distributed in the U.S.A. by DENON ELECTRONICS (USA), LLC. (2) Any product which is not purchased •...
Page 38
• How to Obtain Warranty Performance If your unit ever needs service, it may be taken or shipped to any authorized DENON service station or D&M CANADA INC. (if you are uncertain as to whether • a service station is DENON authorized, please contact D&M CANADA INC. as listed below.) In all other cases, the following procedures apply whenever your unit must be transported for warranty service;...
Page 39
Ie produit, b) reparation ou tentative de reparation par quelqu'un non reconnu par DENON. c) tout envoi du produit (ia reclamation doit etre presentee au transponeur), (5) Anicles sujets deterioration par I'usage (tetes de magnetophone, cellules phono, pointes de lecture phono.