Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tannoy V12HP
Summary of Contents for Tannoy V12HP
- Page 1 USER MANUAL...
-
Page 3: Table Of Contents
12.6 Secur – ET VCS Ceiling Saddle 12.7 Secur – ET VPC Pole Clamp System Configuration & OEM Controllers 13.1 Passive or Biamp ? 13.2 Passive System Parameters (optional) 13.3 Biamp System Parameters V12HP Recommended Service Parts & Accessories Warranty Declaration of Conformity... -
Page 4: Introduction
The V12HP has been designed for use with the Tannoy TX2 controller, which will equalise the system resulting in improved bass performance as well as providing a 2-way crossover function, operating at 100Hz, for use with separate sub-bass systems. -
Page 5: Polarity Checking
Cable choice consists mainly of selecting the correct cross sectional area in relation to the cable length and the load impedance. A small cross sectional area would increase the cables series resistance, inducing power loss and response variations (damping factor). Connectors should be wired with a minimum of 2.5 sq. -
Page 6: Amplification & Power Handling
6. Crossovers The V12HP is supplied as standard for passive operation via the internal crossover network. If higher peak outputs and additional low frequency output is required then the V12HP can be used in... -
Page 7: Arraying
As shown in the above diagram, one of the V12HP cabinets is inverted to allow the optimum splay angle to be achieved. The grill can be simply removed from this cabinet and be replaced in the correct orientation. -
Page 8: Dimensions
9. Dimensions... -
Page 9: Performance Data
Unprocessed Anechoic Frequency Response, 1 watt @ 1 metre Impedance A comprehensive range of measurements including off axis frequency response curves, octave & third octave polar diagrams (single & two cabinet arrays) and beamwidth plots as well as Ease data can be http://www.tannoy.com/ downloaded from... -
Page 10: Technical Specifications
(3) Unweighted pink noise input, measured at 1m in an anechoic chamber All Tannoy V Series products can be used with the Tannoy TDX2 Digital Controller for optimum system performance and when being used with various sub bass systems. Please visit our website at Tannoy operates a policy of continuous research and development. -
Page 11: Rigging & Suspension
Rigging & Suspension 12.1 General Safety Advice The Tannoy Professional hardware covered in this guide has been designed to offer quick, simple, cost effective and secure solutions for mounting specific Tannoy Professional loudspeakers. This hardware has been designed and manufactured with a high safety load factor for its specific role. -
Page 12: Secur - Et Vmy Yoke Bracket
V12HP in both orientations to allow easy adjustment for optimum coverage. The vertical distance between the apex of the VMY and the top of the Tannoy V12HP loudspeaker can be adjusted by connecting to varying mounting points on the bracket allowing varying degrees of vertical rotation. - Page 13 Number on Assembly View (Fig. 3) Fig. 3 Description Hanging Bracket Cross Member Pivot Stud M10 Plain Washer M8 Spring Washer M10 Spring Washer M10 x 30mm Screw M8 x 20mm Screw M10 x 30mm Screw M10 Nyloc Nut Friction Washer 30mm Square Blank Plug Fig.
-
Page 14: Secur - Et Vmb Wall Mounting Bracket
Tannoy V12HP loudspeaker in either portrait or landscape orientations to a wall. The Tannoy V12HP loudspeaker is attached to the bracket using the accessories supplied. This wall-mounting bracket has a larger wall plate than previous models to maximise the integrity of fixing obtained. -
Page 15: Secur - Et Veb Eyebolts
Only use the outer fixing points on the top and sides of the V12HP cabinet for fixing eyebolts. The inner two fixing points on each side of the cabinet are for dedicated bracketry (VMY) only. -
Page 16: Secur - Et Vth Pole Mount
The Tannoy V12HP loudspeaker is fitted as standard with a blanking plate on the base of the cabinet. However, should you ever wish to mount the V12HP onto a standard 35mm pole mount this blanking plate can be quickly and easily removed and replaced by a VTH pole mount. -
Page 17: System Configuration & Oem Controllers
13. System Configuration & OEM Controllers 13.1 Passive or Biamp? The V12HP is supplied as standard for passive operation via the internal crossover network and is connected as shown in Figure 1. To reconfigure for Biamp operation simply follow the wiring schematic as shown in Figure 2. -
Page 18: Passive System Parameters (Optional)
V12HP has been designed to need no external equalisation to overcome system limitations. If the V12HP is to be used alone with additional bass enhancement required and have the frequency response limits tighter than +/- 3dB as stated in section 11, then apply the... -
Page 19: Biamp System Parameters
Type Q / Bandwidth Note : When using the V12HP with subs, set HPF on LF section @ 80 – 110Hz (24dB/oct LR) and omit PEQ1 (on LF only) PEQ 1 (on LF only) may also be omitted when using the V12HP as a floor monitor. -
Page 20: V12Hp Recommended Service Parts & Accessories
Work under warranty should only be carried out by a Tannoy Professional dealer or service agent. This warranty in no way affects your statutory rights. For further information please contact your dealer or distributor in your country. If you cannot locate your distributor please contact Customer Services, Tannoy Ltd at the address given below. -
Page 21: Declaration Of Conformity
16. Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed... - Page 22 Tannoy United Kingdom T: +44 (0) 1236 420199 F: +44 (0) 1236 428230 Tannoy North America T: (519) 745 1158 Tannoy adopts a policy of continuous improvement and product specification is subject to change. E: enquiries@tannoy.com F: (519) 745 2364 E: inquiries@tannoyna.com...