Download Print this page

Advertisement

Angle Grinder
MODEL GA7030, GA7030F
MODEL GA7030S, GA7030SF
MODEL GA7040S, GA7040SF
MODEL GA9030, GA9030F
MODEL GA9030S, GA9030SF
MODEL GA9040S, GA9040SF
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
DOUBLE
INSULATION
M A N U A L
007051

Advertisement

   Summary of Contents for Makita GA7030

  • Page 1

    Angle Grinder MODEL GA7030, GA7030F MODEL GA7030S, GA7030SF MODEL GA7040S, GA7040SF MODEL GA9030, GA9030F MODEL GA9030S, GA9030SF MODEL GA9040S, GA9040SF 007051 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using.

  • Page 2: Specifications

    The mains socket used for this device must be protected with a fuse or protective ....Wear safety glasses. circuit breaker having slow tripping characteristics. For Model GA7030, GA7030F, GA7030S, GA7030SF, ....Only for EU countries GA9040S, GA9040SF For European countries only...

  • Page 3: Safety Instructions

    EN50144. MAKITA INTERNATIONAL EUROPE LTD. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND Responsible manufacturer: Makita Corporation Anjo Aichi Japan SAFETY INSTRUCTIONS ENA001-2 WARNING: When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.

  • Page 4: Additional Safety Rules

    periodically and if damaged have it repaired by an that is damaged should be carefully checked to authorized service facility. Inspect extension cords determine that it will operate properly and perform periodically and replace, if damaged. Keep handles its intended function. Check for alignment of moving dry, clean and free from oil and grease.

  • Page 5

    21. Position the tool so that the power cord always 25. Ensure that ventilation openings are kept clear stays behind the machine during operation. when working in dusty conditions. If it should become necessary to clear dust, first discon- 22. If working place is extremely hot and humid, or nect the tool from the mains supply ( use non badly polluted by conductive dust, use a short- metallic objects ) and avoid damaging internal...

  • Page 6

    FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Shaft lock 006733 CAUTION: • Never actuate the shaft lock when the spindle is moving. The tool may be damaged.

  • Page 7

    NOTE: Models GA7030S, GA9030S, GA7040S, GA9040S, GA7030SF. GA9030SF, GA7040SF and GA9040SF begin to run slowly when they are turned on. This soft start feature assures smoother operation. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

  • Page 8

    Installing or removing wheel guard (accessory) 007049 CAUTION: • The wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. Loosen the lever on the wheel guard. Mount the wheel guard with the protru- sion on the wheel guard band aligned with the notch on the bearing box.

  • Page 9

    For Australia and New Zealand 006747 Mount the inner flange onto the spindle. Fit the wheel/disc on the inner flange and screw the lock nut with its protrusion facing downward (facing toward the wheel). 1. Lock nut 2. Depressed center wheel 3.

  • Page 10

    OPERATION WARNING: • It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. • ALWAYS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work.

  • Page 11

    CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

  • Page 12

    Makita Corporation Anjo, Aichi, Japan 884649B228...

Comments to this Manuals

Symbols: 0
Latest comments: