Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MAXDATA PLATINUM 400 IR
Summary of Contents for MAXDATA PLATINUM 400 IR
- Page 1 MAXDATA PLATINUM 400 IR User’s Manual...
- Page 2 Contents Contents...
-
Page 3: Table Of Contents
Product Regulatory Compliance ......................23 Product Safety Compliance ......................23 Product RoHS Compliance .......................23 Product EMC Compliance .......................23 Product Regulatory Compliance Markings ..................23 Electromagnetic Compatibility Notices ....................23 Europe (CE Declaration of Conformity) ....................23 MAXDATA PLATINUM 400 IR M7 MAXDATA PLATINUM 400 IR M7... -
Page 4: Back Panel Connectors ...................................................................................................................12
Figures 1. Front View ............................7 2. Board Connector and Component Locations ..................10 3. Configuration Jumpers ........................11 4. Back panel Connectors ........................12 5. Installing DIMMs ..........................15 6. Removing the Battery ........................18 7. Clearing the CMOS .........................21 Tables 1. Feature Summary ..........................9 2. -
Page 5: Setting Up The System Safety Information
ESD protection by wearing an antistatic wrist strap attached to chassis ground - any unpainted metal surface - on your server when handling parts. ATTENTION In order to fully separate the server from current, the power cord must be removed from the wall outlet. MAXDATA PLATINUM 400 IR M7... -
Page 6: System Access Warnings
System Access Warnings CAUTION To avoid personal injury or property damage, the following safety instructions apply whenever accessing the inside of the product: • Turn off all peripheral devices connected to this product. • Turn off the system by pressing the power button to off. •... -
Page 7: Powering Up The System
USB 2.0 Port Failure LED Reset Button NIC Activity LED 1 Fan Alarm Mute Button NIC Activity LED 2 (not used in this system) System HDD Activity LED Power Button MAXDATA PLATINUM 400 IR M7 MAXDATA PLATINUM 400 IR M7... -
Page 9: Board Features
• SATA support: Four independent SATA ports support data transfer rates up to 3.0 Gbit/s per port Support for up to four system fans and one processor fan Fans System Management Intel System Management Software ® MAXDATA PLATINUM 400 IR M7... -
Page 10: Connector And Header Locations
Connector and Header Locations Figure 2 shows the approximate location of the major components on board. AA Y S R Q P Figure 2. Board Connector and Component Locations Table 2. Board Connectors and Components Label Description Label Description Video Memory Battery PCI 32/33 Slot 2 2x12 Main Power Connector... -
Page 11: Configuration Jumpers
These pins should be jumpered on 1-2 for normal operation. BIOS Recovery Remove the jumper for BIOS recovery. These pins should be jumpered on 1-2 for normal operation. MAXDATA PLATINUM 400 IR M7 MAXDATA PLATINUM 400 IR M7... -
Page 12: Back Panel Connectors
Back Panel Connectors Figure 4. Back panel Connectors Table 4. Back panel Connectors Label Description Label Description Stacked PS2 Mouse/Keyboard Ports NIC (10/100/1000 Mbps) Serial A USB1-2 Video The NIC LEDs at the right and left of the NIC provide the following information: Table 5. -
Page 13: Hardware Requirements
The use of three DIMMs is not supported. Use DIMMs that are the same type and speed. Use of identical DIMMs is preferred. DIMMs must meet the following requirements: • Use only DIMMs with DDR2 DRAM technology. • Use only DDR2-533 and DDR2-667 stacked DIMM modules. MAXDATA PLATINUM 400 IR M7 MAXDATA PLATINUM 400 IR M7... -
Page 15: Hardware Installations And Upgrades
2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Disconnect the AC power cord from the server. 4. Remove the server‘s cover. 5. Locate the DIMM sockets (see Figure 5). DIMM 2B DIMM 1A DIMM 1B DIMM 2A Figure 5. Installing DIMMs MAXDATA PLATINUM 400 IR M7... - Page 16 6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position (see letter “A” in Figure 5). 7. Holding the DIMM by the edges, remove it from its anti-static package. 8. Position the DIMM above the socket. Align the notch on the bottom edge of the DIMM with the key in the DIMM socket (see letter “B”...
-
Page 17: Replacing The Backup Battery
Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. MAXDATA PLATINUM 400 IR M7 MAXDATA PLATINUM 400 IR M7... - Page 18 To replace the battery, follow these steps: 1. Observe the safety and ESD precautions in “Safety Information”. 2. Turn off all peripheral devices connected to the server. Turn off the server. 3. Disconnect the AC power cord from the server. 4.
-
Page 19: Server Utilities
These parameters can be changed if the user has adequate security rights. If a value cannot be changed for any reason, the feature’s value field is inaccessible. MAXDATA PLATINUM 400 IR M7... - Page 20 Table 6 describes the keyboard commands you can use in the BIOS Setup menus. Table 6. Keyboard Commands Press Description <F1> Help - Pressing F1 on any menu invokes the general Help window. ← → The left and right arrow keys are used to move between the major menu pages. The keys have no affect if a sub menu or pick list is displayed.
-
Page 21: Clearing The Cmos
6. Return the CMOS Clear jumper to the Normal location, covering pins 1 and 2. 7. Close the server chassis. 8. Reconnect the AC power and power up the system. MAXDATA PLATINUM 400 IR M7 MAXDATA PLATINUM 400 IR M7... -
Page 22: Configuring The System For Embedded Serial Ata Raid
Configuring the System for embedded Serial ATA RAID Configuring the BIOS 1. Make sure you are having at least two SATA hard drives. 2. Enter system BIOS Setup by pressing the <F2> key after the Power-On-Self-Test (POST) memory tests begin. 3. -
Page 23: Regulatory And Compliance Information
Europe (CE Declaration of Conformity) This product has been tested in accordance too, and complies with the Low Voltage Directive (73/23/ EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate its compliance. MAXDATA PLATINUM 400 IR M7...