MAXDATA PLATINUM 500 I M5 System Manual
Hide thumbs
Also See for PLATINUM 500 I M5:
- System manual (33 pages) ,
- System manual (35 pages) ,
- Quick start manual (2 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
System Manual
Advertisement
Table of Contents
Related Manuals for MAXDATA PLATINUM 500 I M5
Summary of Contents for MAXDATA PLATINUM 500 I M5
- Page 1 MAXDATA Server PLATINUM 500 I M5 System Manual...
- Page 2 Contents Contents...
-
Page 3: Table Of Contents
Product EMC Compliance – Class A Compliance ..................31 Certifications / Registrations / Declarations ..................31 Product Regulatory Compliance Markings ....................31 Electromagnetic Compatibility Notices ....................31 Europe (CE Declaration of Conformity) ....................31 MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... -
Page 4: Configuration And Bios Select Jumper Locations ..........................................................................12
Figures 1. Back Panel Connectors ........................6 2. The Controls ............................7 3. Server Board Layout ........................11 4. Configuration and BIOS Select Jumper Locations ................12 5. Installing Memory ..........................15 6. Opening Socket Lever and Attaching Processor ................17 7. Replacing the Battery ........................21 8. -
Page 5: Setting Up The System Server Position
In order to fully separate the server from current, the power cord must be removed from the wall outlet. ATTENTION Safety instruction for upright devices: To ensure stability, the floor stands must be turned outwards. MAXDATA Server PLATINUM 500 I M5... -
Page 6: Connecting The System
Connecting the System Back Panel Connectors Figure 1. Back Panel Connectors USB 1 Serial port A USB 2 Video Mouse G. NIC 1 (1 Gbit) Keyboard NIC 2 (1 Gbit) The NIC LEDs at the right and left of each NIC provide the following information. Table 1. -
Page 7: Powering Up The System
HDD Leds. Press the power button one time briefly in order to boot the server. Figure 2. The Controls A. Power switch NIC1 LED Reset switch NIC2 LED Disable Fan Warning HDD LED D. Fan Warning LED Power LED MAXDATA Server PLATINUM 500 I M5... -
Page 9: Server Board Features
• Two 32-bit/33MHz, 5V PCI connectors. Slots 3 and 5 Integrated Capabilities • Integrated 2D/3D graphics controller: ATI Rage™ XL Video Controller with 8 MB of SDRAM Fans Support for up to three system fans and two processor fans continued MAXDATA Server PLATINUM 500 I M5... - Page 10 Server Board Features (Continued) BIOS Intel /AMI BIOS with support for: ® • Advanced Configuration and Power Interface (ACPI) • 8 megabit symmetrical flash memory • Support for SMBIOS Power Management Support for ACPI: • Wake on USB, PCI, RS-232, PS/2, LAN, and control panel Server Management •...
-
Page 11: Server Board Connector And Component Locations
DIMM Sockets (from top to bottom: 1B, Battery 1A, 2B, 2A) +12V CPU Power Connector USB 3 and 4 Header Processor 1 Socket Chassis Intrusion Header Processor 2 Socket Serial B Header MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... -
Page 12: Configuration And Bios Select Jumpers
Configuration and BIOS Select Jumpers CMOS CLEAR BMC Control Force Erase PASSWORD CLEAR Protect Erase RECOVERY BOOT Normal Boot Recovery Boot Figure 4. Configuration and BIOS Select Jumper Locations Table 3. Configuration Jumper [J17] Jumper Name Pins What happens at System Reset CMOS clear If these pins are jumpered, the CMOS settings will be cleared on the next reset. -
Page 13: Hardware Requirements
✏ NOTE Memory sizing and configuration is guaranteed only for qualified DIMMs approved by MAXDATA. The minimum memory configuration is one 256 MB, DDR2-400 MHz DIMM, installed in DIMM socket 1B (the socket farthest from the processors). However, for optimum performance and dual-channel interleave operation, a minimum of two DIMMs should be installed. -
Page 15: Server Board Installations And Upgrades
DIMM2A is the socket closest to the processor socket. ✏ NOTE Memory sizing and configuration is guaranteed only for qualified DIMMs approved by MAXDATA. Installing DIMMs To install DIMMs, follow these steps: 1. Observe the safety and ESD precautions at the beginning of this book. -
Page 16: Removing Dimms
6. Make sure the clips at either end of the DIMM socket(s) are pushed outward to the open position. 7. Holding the DIMM by the edges, remove it from its anti-static package. 8. Position the DIMM above the socket. Align the small notch in the bottom edge of the DIMM with the keys in the socket (see inset in Figure 5). -
Page 17: Installing Or Replacing The Processor
Lower the socket lever completely. ✏ NOTE Make sure the alignment triangle mark and the alignment triangle cutout align correctly. See Figure 6. Figure 6. Opening Socket Lever and Attaching Processor MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... - Page 18 7. Remove the heat sink from its packaging. The heat sink has thermal interface material (TIM) applied to the bottom of it. Be careful not to damage the TIM when you handle the heat sink. 8. Set the heat sink on top of the processor, aligning the captive screws in the heat sink with the standoffs around the processor socket.
-
Page 19: Removing The Processor
8. Reconnect or replace any internal components you needed to disconnect or remove. 9. Replace the server’s cover. Reconnect any external components you needed to disconnect. 10. Attach the AC power cord. MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... -
Page 20: Replacing The Backup Battery
Replacing the Backup Battery The lithium battery on the server board powers the RTC for up to 10 years in the absence of power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) may be wrong. -
Page 21: Replacing The Battery
11. Replace the server’s cover. Reconnect any external components you needed to disconnect. 12. Attach the AC power cord. 13. Run Setup to restore the configuration settings to the RTC. MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... -
Page 23: Server Utilities
If “No” is selected and the <Enter> key is pressed, or if the <Esc> key is pressed, the user is returned to where they were before <F9> was pressed without affecting any existing field values. continued MAXDATA Server PLATINUM 500 I M5... -
Page 24: Clearing The Cmos
Keyboard Commands (Continued) <F10> Save and Exit - Pressing <F10> causes the following message to appear: Setup Confirmation Save Configuration changes and exit now? [Yes] [No] If “Yes” is selected and the <Enter> key is pressed, all changes are saved and Setup is exited. -
Page 25: Clearing The Password
5. Power down the system and disconnect the AC power. 6. Return the Password Clear jumper to the original location, covering pins 5 and 6. 7. Close the server chassis. MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... -
Page 27: Troubleshooting
Power LED Identify the Control panel Green Off = Power is off (off or S5) power state of the On = Power on or S0) system Slow Blink = Low power state (S1–S3) MAXDATA Server PLATINUM 500 I M5... -
Page 28: Bios Error Messages
BIOS Error Messages When a recoverable error occurs during the POST, the BIOS displays an error message describing the problem. Table 5. BIOS Error Messages Error Message Explanation GA20 Error An error occurred with Gate A20 when switching to protected mode during the memory test. Pri Master HDD Error Could not read sector from corresponding drive. -
Page 29: Bios Post Beep Codes
These beeps have a code that identifies system or PCI card events. Before checking for a system beep code error make sure the PCI card is not causing the beeping. MAXDATA Server PLATINUM 500 I M5 MAXDATA Server PLATINUM 500 I M5... -
Page 31: Regulatory And Integration Information
Legally the product is required to comply with Class A emission requirements as it is intended for a commercial type market place. The Server Board has been has been tested and verified to comply with the following electromagnetic compatibility (EMC) regulations when installed in a compatible MAXDATA host system. • EN55022 - Emissions (Europe) •...
Need help?
Do you have a question about the PLATINUM 500 I M5 and is the answer not in the manual?
Questions and answers