Advanced Features - Panasonic KX-FT932FX Operating Instructions Manual

Code #06: Changing the ring setting in TAM/FAX
mode (KX-FT938 only)
TAM RING COUNT
RINGS=2 [±]
To change the number of rings before the unit answers a
call in TAM/FAX mode. You can select "2" (default), "3",
"4", "5", "6", "7" or "AUTO". See page 26 for details.
Note:
L Set feature #77 to "TAM/FAX" (page 35)
beforehand.
Code #06: Changing the ring setting in FAX ONLY
mode (KX-FT938 only)
FAX RING COUNT
RINGS=2 [±]
To change the number of rings before the unit answers a
call in FAX ONLY mode.
You can select "1", "2" (default), "3" or "4".
Note:
L Set feature #77 to "FAX ONLY" (page 35)
beforehand.
Code #10: Changing the maximum recording time
for incoming messages (KX-FT938 only)
RECORDING TIME
=NO LIMIT [±]
"1 MIN": Up to 1 minute.
"NO LIMIT" (default): Unlimited within the voice
memory capacity (page 47).
"GREET ONLY": The unit plays the greeting message
but does not record caller messages.
Code #11: Setting the remote operation ID (KX-
FT938 only)
REMOTE TAM ID
ID=
A 3-digit remote operation ID must be entered when
operating the answering system remotely. This ID
prevents unauthorised parties from listening to your
messages remotely. After you store your remote
operation ID, remote operation is possible.
1. Press {MENU}.
2. Press {#}, then {1}{1}.
3. To activate the remote operation feature, enter a 3-
digit remote operation ID.
L To deactivate the remote operation feature, press
{*}.
4. Press {SET}.
5. Press {MENU}.
Code #13: Setting the dialling mode
DIALLING MODE
=TONE [±]
8. Programmable Features
See page 11 for details.
Code #17: Setting the ringer type for outside calls
EXT RINGER TYPE
=RINGER 1 [±]
To set the ringer type from one of 3 types for outside
calls. You can select "RINGER 1" (default), "RINGER 2"
or "RINGER 3".

8.3 Advanced features

See page 32 for how to enter advanced feature
programming.
Code #22: Setting the journal report to print
automatically
AUTO JOURNAL
=ON [±]
"ON" (default): The unit will print a journal report
automatically after every 30 new fax transmissions and
receptions (page 20).
"OFF": The unit will not print a journal report, but will
keep a record of the last 30 fax transmissions and
receptions.
Code #23: Sending documents overseas
OVERSEAS MODE
=ERROR [±]
If you cannot send a fax overseas even if the number is
correct and the line is connected, activate this feature
before sending the fax.
This feature improves the reliability by reducing the
transmission speed.
"ERROR" (default): When the previous fax transmission
fails and you wish to re-send the document.
"NEXT FAX": This setting is effective only for the next
attempted fax transmission. After transmission, the unit
will return to the previous setting.
"OFF": Deactivates this feature.
Note:
L This feature is not available for broadcast
transmission.
L Calling charges may be higher than usual.
Code #25: Sending a fax at a specific time
DELAYED SEND
=OFF [±]
This feature allows you to take advantage of low-cost
calling hours offered by your telephone company. This
feature can be set up to 24 hours in advance of the
desired time.
To send a document:
1. Insert the document.
2. If necessary, press {A} or {B} repeatedly to select
the desired resolution (page 20).
3. Press {MENU}.
33