Table of Contents
Advertisement
maximum mark (which
is
indicated on the water
reservoir) with luke warm
water, and reinsert back
into the machine.
. Dissolve one packet of
decalcifier (this can be
purchased through the
KRUPS Consumer
Department) in the water
reservoir.
.
Place a cup underneath
the brewing spout.
. Plug machine into elec-
trical outlet.
.
Turn on the machine
using the "On/Off"
button.
.
When the message
"READY" appears in the
display, press the"@"
cup button as if you
were preparing
espresso.
. Allow consecutive
cups
of water/decalcifying
solution to run through
the machine.
.
Refill water reservoir with
clean, fresh water. Allow
machine to cool before
reinserting
stainless
steel brewing sieve back
into the machine.
.
Once machine has
properly cooled down
remove the water reser-
voir,
drip
tray, baffle and
removable overflow grid.
. Turn over the machine
and install the brewing
sieve using a flat headed
screw dirver and turn
counter clockwise until it
is secure.
, ~'
.
Once the water reservoir
is empty, rinse water
reservoir out thoroughly
and refill with fresh, cold
water. Repeat the same
procedure as above until
the water reservoir is
completely emptied.
LCD DISPLAY MESSAGE
DEFINITIONS
CLEAN WATER
The drip tray /s full and
must be emptied.
DECALC
The appliance must be
decalcifying
(See decal-
cifying instructions)
WATER
Fill or reinsert the water
reservoir
COOL
The system has become
too hot, cooling will
automatically
occur, and
then you :can resume
your mode of operation.
SERVICE
The appliance Is not
working accordingly
and
should be sent back to
KRUPS North America
for repair. See last page
of Instruction booklet for
"Guarantee of Perfor-
mance".
PROBLEMS AND
.CAUSES
Problem:
Coffee Leaking
From
Filter Holder
Cause:
.
Filter holder not properly
,
inserted In the machine.
.
Filter holder not pushed
,
in as far as It will go.
. No elasticity In the
brewing head seal.
.' (This may happen after
a
long period of use). The
. part can be ordered
through KRUPS
Customer Service
.
Department.
.
If the seal has lost Its
. elasticity, it must be
replaced with a "New"
one. Allow the appliance
to cool down and then
unscrew the sieve from
. the brewing head.
. Remove the seal careful-
ly from the brewing head
'.
using a screw driver.
.
Place the new seal back
. onto the machine and
then place the flattened
'.
side of sieve back Into
:
the brewing head.
ADDITIONAL INFORMATION
TO "SERVICE"
Self-diagnosis
system:
When .SERVICE.
appears
on display.
disconnect
plug from
supply
source and walt 10 8econds.
Thtn
reconnect the appliance.lf.SERVICE"
appsars again, send sppU.
ance In original
picture-carton
to the neareet service station.
Problem:
f
,;
Pump Makes Loud
Noise
r
. .Cause:
.
No water in the water
. reservoir.
.
Old or dry coffee being
used, water cannot.
properly flow through
thecoffee.
Problem:
Coffee Does Not Come
Out Of Filter Holder
,
Cluse:
.
No water in the water
reservoir.
. Waterreservoir not.
Inserted correctly.
.
Filterblocked because
the coffee mixture Is'too
fine or has been pressed
down too hard.
.
Mach/ne needs to be
decalcified
Problem:
E8presso~es No"Creme"
Cause:
.
Old or dried out coffee
being used.
.
Coffee not suitable for
espresso.
. Coffee ground too,
coarsely.
.
.
Toolittle coffee in the
filter or not properly,
tamped.
~;"9. ' :
;.,
.' ~ ~-''''-I'''1'
i
' .
:
,\! :..;t.".
,,'
t~;~ '<
. ,1/"";."'-":~HJ'.''''7,~~
Problem:
Not Enough Froth When
Frothing Milk
Cause:
.
Steam nozzle Is clogged.
.
Milk is not fresh.
.
The pitcher that you are
using is not suitable. (It
is recommended
that
you use a stainless steel
frothing pitcher). Cold
conducts
better to metal
than to glass or plastic.
.
The type of milk is not
suitable. We recommend
using 2% or skim milk.
Whole milk is okay, but
due to the fat molecules,
it will not have as dense
a froth, as if you were to
use 2% or skim milk.
LIMITED ONE YEAR
WARRANTY
Your
KRUPS product Is
covered by the following
warranty: If, within one year
from the date of purchase,
this KRUPS product fails to
function because of defects
In materials or workman-
ship, KRUPS North
America, Inc., will, at Its
option, repair or replace the
unit without charge,
provided the owner returns:
.
The KRUPS product
(securely packed) and
. proofof dateof
purchase to:
..
'
-
.
KRUPS Customer Service
KRUPS North America, Inc.
7 Reuten Drive
CLOSTER, N.J. 07624
To assure prompt service,
please include a letter indi-
cating the specific cause
for returning your KRUPS
product.
Do not return any
loose parts or any acces-
sories which are not
defective with your appli-
ances to avoid damage
and 108S in transit.
This warranty will be void if
malfunction was caused by
damage to the
product by
accident, misuse, use on
frequency or voltage other
than marked on the product
and/or described in the
instructions, abuse inclu-
ding tampering, damage
in
transit, or use for commer-
cial purposes. This period
warranty gives you specific
legal rights, and you may
also have other rights
which vary from state to
state.
Hide quick links:
Advertisement
Table of Contents
