Advertisement
WaterWorks
...... AUTOMATIC
WATER CONDITIONER
DEMAND TIMER FEATURES,
AND SERVICE
NOTE:
SEE PAGES
10 AND 11 TO SET THE TIMER TO THE CORRECT
TIME OF DAY, WATER
HARD-
NESS NUMBER,
AND RECHARGE
START TIME.
NORMAL
OPERATION,
TIMER DISPLAYS
During normal operation,
the present
f
time of day, and AM or PM, show in
-_.'
/g_,u
/
the time d sp ay area. When
the de- [
J
mend computer
determines
a regen-
eration
is needed,
RECHARGE
TONIGHT
begins to
flash in the display, along with the present
time. RE-
#
#
i
=
= =
w i
a
= a
I
#
# •
I
#
i
i
i
=
•
i
i
D .
i
=
i
III
I
i
i
i
.
=
a j
CHARGE
TONIGHT
flashes
until the
next
regeneration
start
time,
thenl
_.
l-lpM
I
REC_RGE TONIG_ J
changes
to
RECHARGE
NOW, I
-"
which
flashes
until the regeneration
is over.
feature:
OPTIONAL
RECHARGE
CONTROLS
.....................................
Sometimes,
a manually
started
regeneration
(recharge)
may be desired,
or needed.
Two examples
are:
... You have used more water than usual (house guests, extra washing,
etc.) and you may run out of soft water
before the next regeneration.
... You did not refill the storage tank with salt before
it was all gone.
Use 1 of the following
features
to start a regeneration
immediately,
or at the next preset
regeneration
start
time.
RECHARGENOW
!
-"
I-#
J"E_'RGENOW
_"
IC- _u
Press and hold in the TOUCH
- HOLD button until
RECHARGE
NOW starts to flash in the time display
area. The softener
begins an immediate
regenera-
tion, and when over in about 2 hours, you will have
a new supply of soft water. Once started,
you cannot
cancel this regeneration.
RECHARGE
TONIGHT
3:
RECHARGE
TONIGH7
,
Touch (do not hold) the TOUCH - HOLD button,
and
RECHARGE
TONIGHT
flashes
in the time display
area. A regeneration
will occur at the next preset re-
generation
start time. If you decide to cancel this re-
generation,
touch the same button once more.
VACATION
NOTE
..................................................
...
......
......
o,o,.,,=,,
,,
This demand
water softener
regenerates
only when water is used and softening
capacity
must be restored.
For this reason,
the softener
will not regenerate
while you are away from home for extended
periods.
feature:
PROGRAM
MEMORY
...................................................
If electrical
power to the softener
is interrupted,
the
time display
is blank,
but the timer
keeps
correct
time for about 6 hours. When power is restored,
you
have to reset the present
time only if the display
is
flashing.
All other settings
are maintained
and nev-
er require
resetting
unless a change
is desired.
If the time is flashing
after a long power outage,
the
softener
continues
to work as it should
to provide
you with soft water. However, regenerations
may oc-
cur at the wrong time of day until you reset the timer
to the correct
time of day, page 10.
feature / service: AUTOMATIC
ELECTRONIC
DIAGNOSTICS
.......................
The timer
computer
has a self-diagnostic
function
for the electrical
system
(except
input
power
and
water meter).
The computer
monitors
the electronic
components
and circuits
for correct
operation.
If a
malfunction
occurs,
an error code
appears
in the
timer display.
The following
chart (page 18) shows the error codes
that could
appear,
and possible
defects
for each
code. While an error code is displayed,
all timer but-
tons are inoperable
except for the SELECT
button.
SELECT
remains
operational
so
the service
person
can make the
Manual
Initiated
Electronic
Diag-
IE
03
nostics to further isolate the defect,
I-/-
and check the water meter.
17
Advertisement
