Advertisement
Before you start°°°
Your safety and the safety of
others are very important.
We have provided many important
safety messages in this manual and
on your appliance. AM_ays read and
obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You can be killed or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
WARNmNG:
ff the
information
in this manua_
is not followed
exactly,
a
fire or explosion
may
resumt causing
property
damage,
persona_
injury
or
death.
m Do not store
or use
gasoline
or other
flammable
vapors
and
_iquids in the vicinity
of
this or any other
appliance.
WHAT TO DO _FYOU
SMELL
GAS
. Do not try to _ight any
appliance.
. Do not touch
any
electrica_
switch.
. Do not use any phone
in
your
buimding.
. Immediatemy
call your
gas supplier
from
a
neighbor's
phone.
Follow
the gas supp_ier's
instructions.
. ff you cannot
reach your
gas supplier,
call the fire
department.
Installation
and service
must be performed
by a
qualified
installer,
service
agency
or the gas
supplier.
important: Observe all governing
codes and ordinances.
Do not obstruct
flow of combustion
and ventilation
air.
This installation must conform with all
Ioca_ codes and ordinances. In the
absence of local codes, installation must
conform with American National
Standard, National Fuel Gas Code ANSI
Z223.1 --latest
edition _.
It is the customer's responsibility:
• To contact a qualified electrical
installer.
.To assure that the electrical installation
is adequate and in conformance with
National Electrical Code, ANSI/NFPA 70
-- latest edition _, and all codes and
ordinances.
Cabinet opening dimensions shown
must be used. Given dimensions are
minimum clearances.
When installing a range under existing
cabinets and the installation does not
meet the minimum cabinet clearances,
install a range hood above the cooktop
to avoid burn hazards.
Proper installation is your responsibility.
A qualified technician must install this
range. Make sure you have everything
necessary for correct installation. It is the
instdler's responsibility to comply with
installation clearances specified on the
gas information label.The gas
information label and model/serial rating
plate are located on the frame behind the
broiler door.
Mobile
home installation
The installation of this range must
conform with the Manufactured Home
Construction and Safety Standard,Title 24
CFR, Part 3280 [formerly the Federal
Standard for Mobile Home Construction
and Safety, Title 24, HUD (Part 2801]or,
when such standard is not applicable, the
Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1 and
Manufactured Home Installations, Sites,
and Communities ANSl/NFPA 501A'_, or
with local codes.
When this range is installed in a mobile
home, it must be secured to the floor
during transit. Any method of securing the
range is adequate as long as it conforms
to the standards listed above.
Copies of the standards
listed may be
obtained
from:
* CSA international
8501 East Pleasant
Valley Road
C_eveland,
Ohio
44131=5575
_ National Fire Protection Association
One Ratterymarch
Park
Quincy,
Massachusetts
02269
_latedaJs
required:
. gas line shutoff
valve
* 1/2"
male pipe thread
nipple
for connection
to pressure
reguJator
. L,R gas=resistant
pipe=joint
compound
, CSA design=certified
flexible
meta_ appliance
connector
t4=5 feet) or rigid
gas supply
line
as needed
, insulated
pad or 1/4"
plywood
if range
is
installed
over carpeting
safety
1/2"
and 3/8"
Advertisement
