Electrolux E48DF76EPS Installation Instructions Manual
Dual fuel ranges
Hide thumbs
Also See for E48DF76EPS:
- General installation manuallines (5 pages) ,
- Specifications (2 pages) ,
- Design manual (164 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Electrolux E48DF76EPS
Summary of Contents for Electrolux E48DF76EPS
- Page 1 |nstaMMation |nstructions...
- Page 2 MPORTANTSAFEW NSTRUCT ONS Safety Pcecautiens Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Warning or Caution based on the risk type. This isthe safetyalert symbol.
- Page 3 SAFETY PRECAUTIONS...
- Page 5 For toll4ree telephone support in the U.S. and Canada: 1_877_ 4ELECTROLUX (1_877435_3287) For online support and Internet product information: www.e_ectro_uxusa.com @2005 Electrolux Home Products, Inc, Post Office Box 212378, Augusta, Georgia 30917, All rights reserve& Printed in the USA...
- Page 6 TABLE OF CONTENTS Safety ..............Definitions ............2 Important SafetyInstructions ......2 SafetyPrecautions ..........3 Preparingfor mnstaJlation ........7 %rifying Package Contents....... 7 GasSupplyRequirements ......... 7 Gasand ElectricRequirements T able....7 Electrical P owerSupplyRequirements ....8 Gasand EiedHcaiRough-in......9 Cabinet!Counterop P reparation ....... 1 0 OveralDimensions ..........
- Page 7 26,4 Amps E36DF76EPS Wire VAC, (6.3 Kw) 10" Water Column 11" Water Column Liquid Propane 60Hz, 240-4 Natural 4" Water Column 5" Water Column 44.2 Amps E48DF76EPS Wire VAC, (10.4 Kw) 10" Water Column 11" Water Column Liquid Propane 60Hz,...
- Page 8 ELECTRICAL POWER SUPPLY REQUREMENTS It is the owner's responsibility to ensure that the electrical connection of this appliance is performed by a qualified electrician. The electrical installation, including minimum supply wire size and grounding, must be in accordance with the National Electric code ANSIiNFPA...
- Page 9 @AS AND ELECTRiCaL R@U@Ho H A manual shut valve must be installed in the gas piping, external to the appliance, for the purpose of turning on or shutting off gas to the appliance. Plan the location of the range and the gas supply to allow access to the valve when the unit is installed.
- Page 10 for' CABINETAND COUNTE ©P PREPARATION...
- Page 11 Figure 1 (330ram) 10" (254mm) Min. • to combustLble side Minumim wails above the range (both sides) 25" (635mm) E30DF74EPS, E36DF76EPS and E48DF76EPS Cutout Dimensions ModeJ "A..B" E3ODF74EPS 36"(914mm}Recommended 301/16" (764mm} 30"(762mm}Minimum E36DF76EPS 42" (1067mm)Recommended 361/16" (914mm) 3d' (914mm)Minimum E48DF76EPS 54"...
- Page 12 OVERALLD MENS ONS E36DF76EPS and E48DF76EPS Overall Dimensions Side View Figure 2 --30 3/8" (772 ram} Handle font Edge of Bulllnose 29 I/8" (740 ram} --28 //8" (714 ram)- Face of Con[rol panel/Oven Door 1/2" [673 Rear of Corffrol panel/Oven Door 24"...
- Page 13 IISTRLLIIQ THE AITI-TII BRACKET(FOR _", S8'=& 18'=IODELS} Installation of E30DF74EPS Anti-Tip Bracket Figure4 BASE Dimensions from Cabinet Only 30 1/16" (Not Counferfop) (122]mm} FigureS Location of the E30DF74EPS Anti-Tip Bracket REAR Anti-tip bracket location on left rear leg...
- Page 14 Pc÷ ° IISTRLLII@ THE RITI-TIP B_OKET iFOR _'=, 38'=& 41,=IOIELS} Installation of E36DF76EPS Anti-Tip Bracket Top View Figure 6 7 1/2" Back wall (191mm) 24" (610mm 1 Dimensions 18 1/32" from Cabinet Only (458mm) (Not Countertop) 36 1/16" (916mm) Figure 7 Rear "_ Left...
- Page 15 Figure 8 13 5/16" (339mm) BACK WALL 4 9/16" (115mm} All Dimensions " are from Cabinet Only (Not Counfedop) 48 1/16" (1221mm) Figure 9 Rear " Leveler Location of the E48DF76EPS Anti-Tip Leveler 5/16 - 18 × 2 or Equivalent...
- Page 16 @ASR U_T©R AND ELECTRICAL C @N _T Figure 10 ..............................Factory installed j 3/4"regulator (1/2" supply ok) Power cord / Gas Regulator and Electrical Conduit Location Rear View...
- Page 17 38 & 48 ©PT @NAL NSTALUN@ THE BACKGUARDS [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] [] Your Etectrolux Icon range was shipped with a backguard inplace.These instructions cover the installation of one of the optional...
- Page 18 {: { {{:{{??{ Open the door to its fully opened position. Rotate the catch over the retaining on each hinge. Lift the oven door to about a 30 degree angle from the horizontal _osition. Pull the door away from the oven while continuing to lift.
- Page 19 MAK H@THE ELECTRICALCONNECTION Grounding mnstcuctions This appliance must be electrically grounded. With the range positioned directly in front of the cabinet cutout, feed the appliance conduit to the electrical junction box. Then, depending upon Focal codes, utilize one of the following techniques to connect the appliance...
- Page 20 Connectingthe GreenAppliance Wireto the Neutral(White)Supply Wire = WhereLocal CodesPermit Connect the green and white appliance wires to the neutral (white) supply wire in the junction box. Connect the black appliance wire to the black (L1) power supply wire in the junction box, Connect...
- Page 21 Connectingthe GreenAppliance Wireto a GroundedSupply Wire or a GroundedColdWaterPipe= WhereLo_l Codes Permit. Separate the green and white appliance wires. Connect the white appliance wire to the neutral (white) supply wire in the junction box. Connect the black appliance wire to the black (L1) power supply wire in the junction box.
- Page 22 M£K NG THE G£S C©NNECT ON Before sliding the range into the cabinet, connect a flexible gas connector to the gas shut-off valve previously installed on the stub out. The gas valve must be turned off dunng installation. Connect the flex connector to the pipe fitting at the right rear of the range.
- Page 23 Measure from the floor to the countertop and adjust the leveling legs as required position the top frame at the desired height, based on the cabinet and countertop installation. Carefully slide the range into position in the cutout. The rear anti4ip should engage the anti4Jp bracket.
- Page 24 "350" and selecting "BAKE" with the oven selector knob. Rotate each knob to the "Off" position to stop the heating process. For model E48DF76EPS, repeat this test procedure with the companion oven. Test each top burner separately...
- Page 25 ICON Professional series Liquid Petroleum Gas (LPG) Conversion Instructions Freestanding Range Models: E30DF74EPS, E36DF76EPS, E48DF76EPS Model E3ODF74EPS shown This conversion kit shall be installed by a qualified service agency in accordance ----_ WARNING: with the manufacturer's instructions and all applicable...
- Page 26 [] Electrolux I Jc o N • 1/8" flat blade screwdriver * Thread-locker (Loctite 242 or equivalent) • Needle-nose pliers * Burner ring removal tool (provided with conversion kit) • 10 mm open end wrench * U-tube manometer (calibrated) • 6" and 8" long adjustable wrenches °...
- Page 27 Professional Series Range LPG Conversion Kit LPG Conversion Kit for Models E36DF76EPS and E48DF76EPS (36 and 48-Inch) Kit Part Number: 700147-1 Part Number Description (_uantity 65481 BAGr PLASTIC 65480 LABEL, CONVERSION INFORMATION 86007 TOOL, REMOVAL, BUNRER RING 65558 INSTALLATION INSTRCTIONS r LPG CONVERSION KIT...
- Page 28 [] Electrolux [ i c o N 1-'II / :1_ U i_ ,B1 i_l _.1 i[, [=i [,] ile[,] itVL_i_-1 [,] i Move the range out from the wail, if necessary. Remove the grates from the cooktop. If the range is connected to a natural gas supply Remove all of the burner caps and burner rings line, close the gas supply valve.
- Page 29 Professional Series Range LPG Conversion Kit Insert the large end of the burner ring removal Repeat steps 5-1 and 5-2 for the remaining burners. toot into the top of the left rear burner head. Unscrew and remove the nut. Lift out the spill tray. Remove the burner head, Slip the igniter wire off of the burner as you remove it.
- Page 30 [] Electrolux [ Ic o N Make sure all knobs are in the off position, the burner location, The bypass orifice size is stamped on its head, Remove all of the burner knobs from the front of the range, Insert the bypass orifice and the attached o-ring into the right side of the valve with the needle Insert the 1/8"...
- Page 31 Professional Series Range LPG Conversion Kit Remove the two screws that hold the left rear Replace the main orifice with the appropriate burner base to the stove chassis. size from Table 7-1, Match both the model number and the burner location. The main Hold the shutter connector with the 8"...
- Page 32 [] Electrolux [ Ic o N I-'i / ;I "i,i; -I _/r-I_ i_o] i iil "-J iC;_-!-I ! I iC;II [_i_. Connect the U-tube manometer to the LPG Hake sure all knobs on the front of the range supply line.
- Page 33 Professional Series Range LPG Conversion Kit Burner E30DF74EPS E36DF76EPS E48DF76EPS Location (30-Inch) (36-Inch) (48-Inch) Left Rear HN A-0053-E HN A-0053-E HN A-0053-E Left Front HN A-0052-E HN A-0052-E HN A-0052-E Right Rear HN A-0053-E HN A-0052-E HN A-0052-E Right Front...
- Page 34 [] Electrolux I nc o N Make sure that all knobs on the front of the 10-4 10-1 Re-assemble the burner heads, burner head range are in the off position. nuts, burner rings, and burner caps without the spill tray in place. Be sure the igniter wire is 10-2 With electrical power to the range disconnected.,...
- Page 35 Professional Series Range LPG Conversion Kit 12-1 Wait for all the burners to coot. 12-4 Install the spill tray. 12-2 Fill out and apply the conversion labels: 12-5 Replace the burner heads, burner head nuts, burner rings, and burner caps. Be sure the °...
- Page 36 .3C 7.7 Right Front HN A-0053-E .39/9.9 Center Rear HN A-0053-E .38/9.7 Center Front HN A-0053-E .37/9.5 Model E48DF76EPS (48-Inch) The Electrolux Group USA • 250 Bobby Jones Expressway * Augusta, GA 30907 1-877-4electrolux (1-877-453-5287) • www.etectroluxusa,com CANADA • 5855 Terry Fox Way • Mississauga,...