Before you begin installing your single board, please make sure that the following materials have been shipped: Rear I/O bracket X 1 Quick Installation Guide X 1 Driver/Utility CD X 1 Serial ATA Signal Cable X 2 ERX-H61 User’s Manual 3...
4 x STAT II 3.0Gb/s 1 x K/B 1 x Mouse 1 x S/PDIF Out header 1 x RS-232 1 x 24-pin ATX power connecto 1 x 8-pin ATX 12V power connector 1 x CPU fan header 4 ERX-H61 User’s Manual...
HD_LED (Red): Hard Driver LED connector RST (Blue): Reset Switch PWR_ON (Black): Power Switch PWR_LED (Green): Power/Standby LED 2.2.6 Speaker Headers (SPEAK1) This 4-pin connector connects to the PC buzzer speaker. Speaker (Yellow or Black) Pin No. Pin Define ERX-H61 User’s Manual 9...
ERX-H61 User’s Manual 2.2.9 JDVI_HDMI and JME connectors (JDVI_HDMI / JME) Shorten #pin 1-2 to DVI device. If can't be detected, please shorten #pin 2-3 to HDMI. JME: short #pin 1-2 to refresh your ME ERX-H61 User’s Manual 11...
ERX-H61 Use’s Manual 3. BIOS Setup Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. 14 ERX-H61 User’s Manual...
If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to. Press F1 to Continue, DEL to enter SETUP ERX-H61 User’s Manual 15...
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1 key again. 16 ERX-H61 User’s Manual...
Note: The BIOS setup screens shown in this chapter are for reference purposes only, and may not exactly match what you see on your screen. Visit the Avalue website (www.avalue.com.tw) to download the latest product and BIOS information. ERX-H61 User’s Manual 17...
[Hour],[Minute]and [Second]. 3.5.2 Advanced Setting • Onboard Lan BootROM Control These items can change Boot ROM of the LAN chipset. • Launch Storage OpROM Setting old equipment storage ROM open and close, optional for Enalbed, Disbaled. 18 ERX-H61 User’s Manual...
Page 19
Select the highest ACPI sleep state the system will enter when the suspend button is pressed. Optional for Suspend Disbled、S1(CPU Stop Clock)、S3(Suspend to RAM). • Lock legacy Resources Enables or disables lock of legacy resources. optional for Enalbed, Disbaled. ・Press <Esc> key to return to "Advanced" menu. ERX-H61 User’s Manual 19...
Page 20
Hr::min::sec specified. • Wake system with Dynamic Time Enable or disable system wake on alarm event. When enabled, system will wake on the current time + Increase minute(s). ・Press <Esc> key to return to "Advanced" menu. 20 ERX-H61 User’s Manual...
Page 21
Setting hyper-threading technology open or closed. •Active Processor Cores Setting processor core number. •Limit CPUID Maxinum When set to [Enabled], this item limits the CPUID maximum value to 3, which is usually required for older OS like Windows NT4.0. ERX-H61 User’s Manual 21...
Page 22
Setting of CPU C energy-saving depth. •Local x2APIC This item enables Local x2APIC. Some OSes do not support this feature. •Press <Esc> key to return to "Advanced" menu. ► USB Configuration Click <Enter> key to enter its submenu. 22 ERX-H61 User’s Manual...
Page 23
NVRAM before you can start up the system. But by doing this, you will have to reset all previously set options. • Power On By PS/2 Mouse Set the mouse boot function. ERX-H61 User’s Manual 23...
Page 24
• Smart Fan Configuration Allows you to determine whether to enable the CPU fan speed control function and adjust the fan speed. Available options: Manual Mode, Smart Mode • Fan PWM Value Available options: 0 – 255 24 ERX-H61 User’s Manual...
Low MMIIO resources align at 64MB/1024MB. • DMI Gen2 DMI Gen2 Enabled/Disabled. • VT-d Available options: Enabled, Disabled • Initate Graphic Adapter Select which graphics controller to use as the primary boot device. • IGD Memory ERX-H61 User’s Manual 25...
Page 26
Sets the HD Audio has Enabled or Disabled state. • Azalia internal HDMI codec Enabled/Disabled internal HDMI codec for Azalia. • USB2.0 Controller Enabled/Disabled All USB Devices. ► SATA Control Click <Enter> key to enter its submenu. 26 ERX-H61 User’s Manual...
Page 27
Click <Enter> key to enter its submenu. • DVMT Mode Select Select DVMT Mode used by Internal Graphics Device. • DVMT/FIXED Memory Select DVMT/FIXED Mode Memory size used by Internal Graphics Device. ・Press <Esc> key to return to "Chipset" menu. ERX-H61 User’s Manual 27...
Page 28
Click <Enter> key to enter its submenu. • ME Subsystem Available options: Disabled,Enabled • ME Temporary Disable Available options: Disabled,Enabled • End of Post Message Available options: Disabled,Enabled ► ME Subsystem Click <Enter> key to enter its submenu. 28 ERX-H61 User’s Manual...
Page 29
• Bootup NumLock State Allows you to select the power-on state for the NumLock. • Full Screen Logo This item determines to show the full screen logo when booting. • Option ROM Messages Set display mode for option ROM. ERX-H61 User’s Manual 29...
Page 30
• User Password The option be used to set the user password, setting steps is same with "Administrator Password" Setting way. Note: Don’t forget your password. If you forget the password, you will have to open the 30 ERX-H61 User’s Manual...
Page 31
But by doing this, you will have to reset all previously set options. 3.5.6 OverClock Setting ► CPU Configuration Click <Enter> key to enter its submenu.The following items: setting CPU Multiplier, CPU power consumption limit, power consumption limit, overclocking switch. ERX-H61 User’s Manual 31...
Page 32
Click <Enter> key to enter its submenu.The following items: Setting FSB and memory parameters act. ► Graphics Configuration Click <Enter> key to enter its submenu. The following items: setting graphics core ratio limit, graphics voltage, iGFX core current max. 32 ERX-H61 User’s Manual...
Page 33
BIOS setup program. Select "No" or press "ESC" and return to the main menu. • Save Changes and Reset Select "Save Changes and Reset", and select "Yes" and press <Enter> to save the ERX-H61 User’s Manual 33...
Page 34
BIOS default values, select "No" or press "ESC" return to the main menu. • Restore User Defaults Select "Restore User Defaults", select "Yes" and press <Enter> allows the user to restore the user's personality BIOS settings, select "No" or press "ESC" and return to the main menu. 34 ERX-H61 User’s Manual...
ERX-H61 User’s Manual 4. Drivers Installation Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. ERX-H61 User’s Manual 35...
Windows XP operation system. If the warning message appears while the installation Step 3. Click Next. process, click Continue to go on. Step1. Locate 「\Driver_Chipset\Intel\ H61\ infinst_autol.exe」. Step 4. Click Finish to complete setup. Step 2. Click Next. 36 ERX-H61 User’s Manual...
Windows XP operation system. Step 3. Select Next to the next step. Step 1. Locate 「\Driver\Audio\Realtek Step 4. Click Finish to complete the setup. HD\XP\setup.exe」. Step 2. The program executes the Setup automatically. 38 ERX-H61 User’s Manual...
\Driver_Network\Realtek PCIE. Note: The installation procedures and screen shots in this section are based on Windows XP operation system. Step 3. Click Finish to complete the setup. Step 1. Locate 「\Driver\LAN\Realtek PCIE\XP\setup.exe」. Step 2. Setup executing. ERX-H61 User’s Manual 39...