Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE AND
OPERATING MANUAL
ProSwitch
-Quad Series
Modular Ethernet Fiber and Copper Switching
CORPORATE HEADQUARTERS
5001 American Blvd., W. Suite 605
Phone: 800.441.5319
E-mail:
debbieh@watersnet.com
www.watersnet.com
MANUFACTURING/CUSTOMER SERVICE
th
945 37
Avenue, NW
Phone 800.328.2275
E-mail: carolynl@watersnet.com
1.0
SPECIFICATIONS
1.1
Technical Specifications
Performance
Aggregate Filtering Rate:
2,380,800 frames/sec for 16 100Mbps ports
(for ProSwitch-QS5116)
(all ports are wire speed)
1,190,400 frames/sec for 8 100Mbps ports
(for ProSwitch-QS580 & -QS5108)
Aggregate Forwarding Rate:
(for ProSwitch QS Fast Ethernet ports)
(all ports are wire speed)
1,190,400 frames per second, 16-port units
595,200 frames per second, 8-port units
Data Rate:
10Mbps and 100Mbps
Address Table Capacity:
24K node addresses, self-learning (12K on 8-port models), with
address aging
Packet buffer size :
8 MB dynamic (4MB for 8-port)
Latency:
5 µs + packet time (100 to 100Mbps)
15 µs + packet time (10 to 10Mbps, and 10 to 100Mbps)
Network Standards
Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T, IEEE 802.3u: 100BASE-TX, 100BASE-FX
Maximum 10Mbps Ethernet Segment Lengths
Unshielded twisted pair
100 m (328 ft)
Shielded twisted pair
150 m (492 ft)
10BASE-FL multimode fiber optic
2 km (6,562 ft)
10BASE-FL singlemode fiber optic
10 km (32,810 ft)
Maximum Standard Fast Ethernet Segment Lengths:
10BASE-T (CAT 3, 4, 5 UTP)
100BASE-TX (CAT 5 UTP)
Shielded twisted pair
100BASE-FX, half-duplex, multimode
100BASE-FX, full duplex, multimode
100BASE-SX, short wavelength HDX m.m.
100BASE-FX, half-duplex, singlemode
100BASE-FX, full duplex, singlemode
Connectors for copper wiring
Twisted Pair at 10/100Mbps: RJ45 shielded, female, front mounted
(for ProSwitch Quad-Series Fast Ethernet copper ports, use Cat 5 cable)
Fiber Multimode connector types:
Fiber Port, SC-type (snap-in): Fiber optic multimode, 100BASE-FX
Fiber Port, ST-type (twist-lock): Fiber optic multimode, 100BASE-FX
Fiber Port, MTRJ-type (plug-in): Fiber optic multimode, 100BASE-FX
Fiber Port, VF45-type (plug-in): Fiber optic multimode, 100BASE-FX
Fiber Port, ST-type (twist-lock): Fiber optic multimode, 10ASE-FL
Fiber Singlemode connector types:
Fiber Port, SC-type: Fiber optic singlemode, 100BASE-FX
Manual switch-selections and jumpers
Up-link Push-button: Crossover sw for one RJ45 port per QPM-xxx
Fiber default: Full duplex (Internal jumpers may select HDX mode)
ProSwitch Quad-Series Fiber Switches
Installation and User Guide
100 m (328 ft)
100 m (328 ft)
150 m (492 ft)
412 m (1350 ft)
2.0 km (6,562 ft)
300 m ( 935 ft)
412 m (1350 ft)
15.0 km (49,215 ft)
Page 1
Advertisement
Table of Contents
Related Manuals for Waters Network Systems ProSwitch-Quad Series
Summary of Contents for Waters Network Systems ProSwitch-Quad Series
- Page 1 SPECIFICATIONS Technical Specifications Performance Aggregate Filtering Rate: 2,380,800 frames/sec for 16 100Mbps ports (for ProSwitch-QS5116) (all ports are wire speed) 1,190,400 frames/sec for 8 100Mbps ports (for ProSwitch-QS580 & -QS5108) Aggregate Forwarding Rate: (for ProSwitch QS Fast Ethernet ports) INSTALLATION GUIDE AND (all ports are wire speed) 1,190,400 frames per second, 16-port units 595,200 frames per second, 8-port units...
- Page 2 To validate the product warranty, please complete and return the enclosed Product Registration Card to Waters Network Systems as soon as possible. In the event there are items missing or damaged, contact the party from whom you purchased the product.
- Page 3 Product Description - ProSwitch Quad-Series Fiber Switches FDX/HDX ProSwitch Quad-Series Fiber Switches boost the performance of large Ethernet LANs, and have the flexibility of both fiber and twisted-pair switched ports. Their “mixed-media” capability provides for a variety of configurations including various types of fiber port connectors and modes, as well as allowing a mix of 10/100Mbps RJ45 (copper) ports in the same unit.
- Page 4 module is equipped with a Media Dependent Interface-Crossover (MDI-X) push-button switch to simplify 2.2.5 Combo “3 + 1” Quad Port Modules, 3@RJ45 and 1@fiber cascaded or up-link connections. The combo quad-port modules are combination of copper and fiber media, available as three 10/100-switched RJ45 copper ports and one 100Mbps switched multimode fiber ST or SC or singlemode SC-type FDX/HDX port.
- Page 5 The latency (the time the frame spends in the Switch before it is sent along or forwarded to its Quad-Series switches enables them to inter-connect a series of subnets (one subnet per Q-Series destination) of the Quad-Series switches varies with the port-speed types, and the length of the frame is a switch) in a LAN traffic center.
-
Page 6: Installation
probable growth of the central switch is towards more fiber backbone segments, then two quad-port fiber of the QPMs. QPMs are selected to provide 6 required fiber ports and two for spares and/or future backbone The various media types supported along with the corresponding IEEE 802.3 and 802.3u expansion. - Page 7 the cladding respectively). Singlemode fiber allows full bandwidth at longer distances, and may be used RJ45 ports, internal jumper settings for 10/100Mbps (auto-negotiation) or for fixed Half- or to connect 10Mbps nodes up to 10km apart, or 18km with the QPM-SSC. Full-Duplex @ 100Mbps, per port The same procedures for multimode fiber applies also to singlemode fiber connectors.
- Page 8 Combo(3+1) ports, internal jumper settings for 10/100 RJ45 Auto-Negotiation or 100Mbps Note: For 10Mbps fiber ports, the user can set the jumpers either at full duplex or half duplex on all the fiber fixed Half- or Full-Duplex , per port four ports.
-
Page 9: Operation
Caution: Be careful not to disturb the power supply. Step 7 The figure below shows the top view of QPM Card after successfully installed the QPM cards Looking down into the ProSwitch Q- inside the QS5116. Series unit, notice that there are individual AC Power Input QPM connector sockets along with two stand- Jumper Settings for HDX/FDX... - Page 10 The ProSwitch Quad-Series switches operate in the store-and-forward switching mode, which When Quad-Switch’s RJ45 copper ports are set for auto-negotiation and connected to another eliminates bad packets and enables peak performance to be achieved when there is heavy traffic on the auto-negotiating device, there are 4 different speed and F/H modes selection depending on what the network.
- Page 11 transmitter to start sending the packets. Of course, the transmitting device must also support the 802.3x This section applies only to QPMs shipped as separate items, i.e., QPMs not factory installed in a flow control standard in order to communicate properly during normal operation. ProSwitch Quad-Series QPM slot.
- Page 12 5.2.2 QPM-MSC 100Mbps multimode FX-SC Quad-port, “snap-in” connector ProSwitch QPM-MV45 is a quad-port multimode fiber FX “small-form-factor” VF45 connector used primarily in 100Mbps fiber-to-the-desktop links. Its size is similar to the MT-RJ port, but the VF45 The ProSwitch QPM-MSC is a multimode 100Mbps fiber optic shell is slightly larger.
-
Page 13: Troubleshooting
Each 3+1 combo port has an Activity (ACT) LED indicating packets being received, a Link (LK) Quad-Series unit (or if unknown, contact Waters Network Systems) by fax, phone or email for assistance. LED that indicates proper connectivity with the remote device when lit, a FDX/HDX LED to indicate full- duplex mode when lit (or half-duplex when off). - Page 14 All returns for repair must be accompanied by a Return Material Authorization (RMA) number. To workmanship for a period of three (3) years from the date of shipment by Waters Network Systems. obtain an RMA number, contact Waters Network System Customer Support at 800.328.2275 (office hours: 8AM - 5PM Central Standard Time).