Step 1, Remove Packaging; Step 2, Install Water Line - GE ZlS360N Design & Installation Manual

Installation Instructions
[STEP 1] REMOVE PACKAGING
CAUTIO N:
Relrigerator is much hea, ier at the
top than at the botton/ - be careflll when moxing.
X4hen usim* a hand track, handle fl'om side onE.
PRUDENCE: i,e
plus lourd en haut qu'en bas. ll taut 6tre prudent lots
des d_placements. Si tm diable est utilis_, il taut
soulexer le r_frig&'atetu _sur le c'6t_ seulement.
• Careflflly cut banding at the top and bottom,
reulove otlter carton.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
NOTE: IT IS NOT NE(:ESSARY TO lAY CABINET
DOWN IN ORDER TO REMOVE SKID!
• The unit is secured to the skid with 4 slotted
tie-down straps. Remove the four 5/16" bolts
fl'om the base channels in the tie-downs.
• Remoxe the fore" 7/16"
bolts secm'ing the straps
to the skid.
CAUTION: 1,oNOS
ATTEMPT TO ROI,I,
UNIT OFF SKID.
Remove
Tie Downs
,/
PRUDENCE: n,NE
FAUT PAS ESSAYER DE
FAIP,E ROUI,EP, I,E
I)d_FI_,IGt_RATE/_,rl ). POUR
I/ENI,EVER DE I__Y
PA1,ETTE.
• SuI)port blocks on the bottom of the refl'igeration
case must be removed befl_re the refl'igerator is
taken off the skid or damage will occm'. Careflflly;
tilt refl'igerator and slide blocks out from beneath.
• Remove toekick, set aside fin" final installation.
• I,itt the refl]gerator off the skid with an appliance
dolly. Handle from the sides.
[STEP 2] INSTALL WATER LINE
• A cold water SUl_ply is required fin" automatic
icemaker operation. The water pressure must be
between 40 and 190 p.s.i.
• Route l/4"
OD COl)per or GE SmartConnect
'_
plastic tubing between house cold water line and
the water connection location.
• Tubing should be long enough to extend to the
fl'ont of the refl'igeratm: Allow enough tubing to
accommodate bend leading into the water line
connection.
NOTE: The only GE approved plastic tubing is
suI)plied in the GE Sulart(_onnect
TM
Refl'igerator
Tubing kits. Do not use any other plastic water sui_ply
line because the line is trader pressure at all times.
Other types of plastic mav crack or mptm'e with age
_lll(1 Catlse
water dalnage to VO/lI" houle.
GE SmartCmmect "_Refl'igerator Tubing Kits are
available in the fi_llowing lengths:
2' (.6 m) WXO8XIO002
6' (1.8 m) WXO8XIO006
15' (4.6 m) X,_3XOSXIO015
25' (7.6 m) X,_3XOSXlO025
CopperTubingJ
Shut off the main water supply.
Turn on the nearest taucet long enough to clear the
line of water.
• Install a shut-off wflve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-oft valve should be located where it will
be easily accessible,
• Turn on the main water SUl)ply and flush debris.
Rtm about a quart of water through the tubing into
a bucket. Shut off water sui)ply at the shut-off wflve.
NOTE: Saddle tyi)e shut-off wflves are included in
many water sui)ply kits. Befln'e pro'chasing, make
stu'e a saddle type wflve complies with yore" local
phunbing codes.
NOTE:
Commonwealth of Massachusetts Phunbing
Codes 248CMR shall be adhered to. Saddle wflves
are illegal and use is not permitted in Massachusetts,
Consult with votu" licensed phunber.
11